Bedienungsanleitung Bosch PFS 3000-2 (Seite 23 von 274) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544011

Zoom out

Zoom in

Vorherige Seite

1/274

Nächste Seite

English | 23

Bosch Power Tools 2 609 007 771 | (28.2.14)

Adjusting the Air Flow (see figure D)

(AIRVolume)

– Set the sliding switch 24 to the appropriate application to

set the correct air flow and pressure for the spray material

used.

Work Breaks and Transport (see figures K – L)

A carrying handle 22 and a carrying strap 21 are fitted to the

base unit to enable easy transport of the fine-spray system.

You can hang the base unit 20 across your shoulder during

work using the carrying strap 21.

The spray gun 1 can be put down on a flat work surface during

breaks. No spray material can leak out.

 Always put the spray gun upright on a flat surface when

it is filled with spray material. Spray material can leak

out from a spray gun if it is lying down.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself, pull the mains

plug.

 Thoroughly clean the individual parts of the fine-spray

system after each use, especially all paint-carrying

components. Proper cleaning is a prerequisite for fault-

less and safe operation of the spray gun. No warranty

claims will be accepted if cleaning has not been done at all

or has not been done properly.

If the replacement of the supply cord is necessary, this has to

be done by Bosch or an authorized Bosch service agent in or-

der to avoid a safety hazard.

Cleaning (see figure M)

Always clean the spray gun and the container with the respec-

tive diluting agent (paint thinner or water) for the spray mate-

rial being used.

Never clean the nozzle and air holes in the spray gun with

pointed objects.

– Switch the base unit 20 off.

– Remove the air hose 18 both from the base unit 20 and

from the spray gun 1 (quarter turn of the bayonet lock 19

counterclockwise; pull the bayonet lock 19 out of the port

8/27).

– Clean the base unit if necessary with a cloth moistened

with diluting agent and then remove the base unit 20 and

the air hose 18 from the immediate cleaning environment.

– Press the trigger switch 5 on the spray gun so that the

spray material can flow back into the container.

– Unscrew the container 7 and empty the remaining spray

material back into the original spray material.

– Fill the container 7 halfway with the diluting agent (solvent

or water) and fit it to the spray gun 1 again.

– Shake the spray gun several times.

– Unscrew the container 7 and empty the container com-

pletely into an empty material tin.

– Remove the union nut 3, the air cap 2, the nozzle cap used

9/10 and the suction tube 15 with the container seal 14.

– Clean all paint-carrying parts in a bucket with diluting agent

using the cleaning brush 25 or a standard washing-up

brush.

Also clean the paint channel 17 of the spray gun 1.

– Check if the suction tube 15 and the container seal 14 are

free of spray material and undamaged.

If required, clean the container seal 14 again with diluting

agent.

Clean the ventilation hole 16 using the cleaning brush 25.

– Clean the outside of the container and the spray gun with a

cloth moistened in paint thinner.

– If required, clean the filling sieve 11 thoroughly with dilut-

ing agent.

– Before mounting, allow all components to dry thoroughly.

– Reassemble the fine-spray system in reverse order.

Cleaning the Air Filter (see figure N)

The air filter 29 must be cleaned occasionally. The air filter

must be replaced if it is heavily soiled.

– Open the air filter cover 26.

– Remove the air filter 29.

– Light soiling:

Tap the air filter 29 to empty it.

Heavy soiling:

Clean the air filter 29 under running water and then leave it

dry thoroughly to prevent mould from forming.

Replace the air filter 29.

– Reinsert the air filter.

– Close the air filter cover 26 again.

Spraying capacity Adjustment

Too much material on target ar-

ea:

The spraying capacity must

be reduced.

– Turn down by one set-

ting.

Not enough material on target

area:

The spraying capacity must

be increased.

–Turn up by one setting.

Off “Wood” application “Wall” application

Thin-viscosity spray

material

Thick-viscosity spray

material

OBJ_BUCH-2024-002.book Page 23 Friday, February 28, 2014 9:28 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PFS 3000-2 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info