Bedienungsanleitung Bosch PMF 350 CES Multitool (Seite 19 von 129) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

708263

Zoom out

Zoom in

Vorherige Seite

1/129

Nächste Seite

Application tool Material Application

Bi-metal segment

serrated blade

Insulation material, insula-

tion boards, floor panels,

impact sound insulation

boards, cardboard, car-

pets, rubber, leather

Precise cutting of soft materials;

example: Cutting insulation boards to size, cutting pro-

truding insulation material to length so that it is flush with

the surface

TC-Riff sanding fin-

ger

Wood, paint Sanding of wood or paint in hard-to-reach areas without

sanding paper;

example: Sanding off paint between window shutter slats,

sanding wooden flooring in corners

TC-Riff plunge cut

saw blade

Fibreglass, mortar, wood Plunge cuts in extremely abrasive materials;

example: Routing of thin mosaic tiles

HCS universal joint

cutter

Expansion joints, window

putty, insulation materials

(rock wool)

Cutting soft materials;

example: Cutting silicone expansion joints or window

putty

Bi-metal plunge cut

saw blade for wood

and metal

Softwood, hardwood,

veneered boards, plastic-

coated boards, non-

hardened nails and

screws

Fast, deep plunge cuts in wood and metal;

example: Fast cutting of wood containing nails, deep

plunge cuts in laminated boards and precise shortening of

door frames

Bi-metal plunge cut

saw blade for wood

and metal

Wood, abrasive wood-

based materials, plastics,

hardened nails and

screws, non-ferrous metal

pipes

Fast, deep plunge cuts in wood, abrasive wood-based ma-

terials and plastics;

example: Fast cutting of non-ferrous metal pipes and pro-

files with small dimensions, easy cutting of non-hardened

nails, screws and steel profiles with small dimensions

TC plunge cut saw

blade, metal

Stainless steel, screws

and nails, epoxy resin,

fibreglass-reinforced

plastics, fibreglass, plas-

terboard, porous concrete

Fast, deep plunge cuts in severely abrasive materials or

metal;

example: Fast cutting of kitchen front covers, easy cutting

through hardened screws, nails and stainless steel.

HCS plunge cut

saw blade for wood

Softwood, dowels, pins,

furniture elements

Fast, deep separating cuts and plunge cuts;

including sawing close to edges in corners and in difficult-

to-reach areas;

example: Deep plunge cut in softwood for installing a vent-

ilation grille

Fitting/changing the application tool (AutoClic)

(see figuresA–B)

Remove the application tool if one has already been fitted.

To do so, open the AutoClic lever(1) all the way. The applic-

ation tool/accessory will be ejected.

Place the required application tool (e.g. plunge cut saw

blade(9)) on a level surface so that the depressed centre is

face down (see figure on the graphics page; you should be

able to read the text on the application tool from above).

Turn the application tool to a position which is convenient

for the job at hand. Press the power tool onto the application

tool at the required angle until it audibly engages.

u Check that the application tool is seated securely. Ap-

plication tools that are attached incorrectly or are not se-

curely fixed in place may come loose during operation,

thereby putting you at risk.

Fitting and Adjusting the Depth Stop

The depth stop (12) can be used when working with seg-

ment saw blades.

Remove the application tool if one has already been fitted.

Slide the depth stop (12) over the tool holder (8) and onto

the collar of the power tool as far as it will go, with the la-

belled side facing upwards.

The depth stop is intended for the following cutting depths:

– With segment saw blades ACZ85.. with a diameter of

85mm: Cutting depths 8mm, 10mm, 12mm and

14mm (information on the depth stop in a larger font size

and without brackets).

– With segment saw blades ACZ100.. with a diameter of

100mm: Cutting depths 14mm, 16mm, 18mm and

20mm (information on the depth stop in a smaller font

size and in brackets).

English | 19

Bosch Power Tools 1 609 92A 4K3 | (12.10.2018)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PMF 350 CES Multitool Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info