Bedienungsanleitung Bosch PMF 350 CES Multitool (Seite 21 von 129) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

708263

Zoom out

Zoom in

Vorherige Seite

1/129

Nächste Seite

Always connect a dust extraction system for sanding.

Remove the application tool and the depth stop (12) for fit-

ting the dust extraction system (17) (accessory).

Slide the dust extraction system (17) as far as it will go over

the tool holder (8) onto the collar of the power tool. Turn the

dust extraction system to the required position (not directly

under the power tool). Push the clamping lever (18) shut to

fix the dust extraction system in position.

Plug the tool sleeve of the extraction hose (15) onto the ex-

traction outlet (16). Connect the dust extraction hose (15)

to a dust extractor (accessory).

You will find an overview of how to connect various dust ex-

tractors at the end of these operating instructions.

The dust extractor must be suitable for the material being

worked.

When extracting dry dust that is especially detrimental to

health or carcinogenic, use a special dust extractor.

Operation

Starting Operation

u Pay attention to the mains voltage. The voltage of the

power source must match the voltage specified on the

rating plate of the power tool.

u Products that are only sold in AUS and NZ: Use a resid-

ual current device (RCD) with a nominal residual current

of 30 mA or less.

Switching On/Off

u Make sure that you are able to press the On/Off switch

without releasing the handle.

To switch on the power tool, slide the on/off switch (2) for-

ward so that "I" appears on the switch.

The electronic soft start limits the torque when the power

tool is switched on and increases the service life of the mo-

tor.

The Constant Electronic keeps the orbital stroke rate at no

load and under load virtually consistent, guaranteeing uni-

form performance.

To switch off the power tool, slide the on/off switch (2)

backwards so that "0" appears on the switch.

The 180° light band(7) improves visibility in the immediate

work area. It is automatically switched on and off with the

power tool.

u Do not look directly into the worklight; it can blind

you.

Preselecting the orbital stroke rate

You can even preselect the required orbital stroke rate dur-

ing operation using the orbital stroke rate preselection

thumbwheel (4).

The required orbital stroke rate is dependent on the material

and the work conditions and can be determined using prac-

tical tests.

Orbital stroke rate level “6” is recommended for sawing, cut-

ting and sanding harder materials, such as wood or metal;

orbital stroke rate level “4” is recommended for softer ma-

terials, such as plastic.

Practical Advice

u Pull the plug out of the socket before carrying out any

work on the power tool.

u Always wait until the power tool has come to a com-

plete stop before placing it down.

Note: Do not keep the ventilation slots (3) on the power tool

closed when working as this will reduce the service life of the

power tool.

Operating principle

The oscillating drive causes the application tool to oscillate

back and forth by 2.8° up to 20000 times per minute. This

enables precise work in the tightest of spaces.

Use a consistent, low contact pressure

when performing work; otherwise, the

performance will be impaired and the ap-

plication tool may jam.

While working, move the power tool back

and forth to prevent the application tool

overheating and jamming.

Sawing

u Use only undamaged saw blades that are in perfect

condition. Bent or dull saw blades can break, negatively

influence the cut, or lead to kickback.

u When sawing lightweight materials, take into account

the statutory provisions and recommendations of the

material manufacturers.

u Plunge cuts may only be applied to soft materials,

such as wood, gypsum board, etc.

Before using HCS saw blades to saw into wood, chipboard,

building materials, etc., check these saw blades for foreign

objects, such as nails, screws, etc. Remove the foreign ob-

jects as required or use bi-metal saw blades.

Cutting

Note: When cutting wall tiles, please bear in mind that the

application tools are subject to high wear if used for exten-

ded periods.

Sanding

The material removal rate and sanding result are primarily

determined by the choice of sanding sheet, the preselected

orbital stroke rate level and the contact pressure.

Only immaculate sanding sheets achieve good sanding per-

formance and make the power tool last longer.

Be sure to apply consistent contact pressure in order to in-

crease the lifetime of the sanding sheets.

Excessively increasing the contact pressure will not lead to

increased sanding performance, rather it will cause more

severe wear of the power tool and of the sanding sheet.

English | 21

Bosch Power Tools 1 609 92A 4K3 | (12.10.2018)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PMF 350 CES Multitool Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info