Bedienungsanleitung Bosch PMF 350 CES Multitool (Seite 20 von 129) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

708263

Zoom out

Zoom in

Vorherige Seite

1/129

Nächste Seite

20 | English

1 609 92A 4K3 | (12.10.2018) Bosch Power Tools

Insert the appropriate segment saw blade for the desired

cutting depth. Slide the depth stop (12) from the tool holder

(8) in the direction of the application tool until you can ro-

tate it freely. Rotate the depth stop (12) so that the desired

cutting depth is above the section of the saw blade that will

be used to saw. Slide the depth stop (12) onto the collar of

the power tool once again as far as it will go.

Remove the depth stop (12) for all other cutting depths and

for working with other application tools. To do this, remove

the application tool and pull the depth stop away from the

collar.

Fitting the Auxiliary Handle (accessory)

The low-vibration auxiliary handle enables the tool to be

used safely and more comfortably.

Screw the auxiliary handle into the thread (5) on the left or

right of the machine head depending on how you are work-

ing.

u Do not continue to use the power tool if the auxiliary

handle is damaged. Do not make any alterations to the

auxiliary handle.

Choosing the Sanding Sheet

Different sanding sheets are available, depending on the material you are working with and the required surface removal rate:

Sanding sheet Material Application Grit

Red quality

– All wood and wood-

based materials (e.g.

hardwood, softwood,

chipboard, construction

boards)

– Metal materials

For pre-sanding, e.g. of rough and uneven beams and

boards

Coarse 40

For surface sanding and levelling of slight irregularities Medium 80

100

120

For finish-sanding and fine sanding of wood Fine 180

240

320

400

White quality

– Paint

– Varnish

– Filler

– Bodyfiller

For sanding down paint Coarse 40

For sanding undercoats (e.g. removing brushstrokes,

paint drips and paint runs)

Medium 80

100

120

For final sanding of primers prior to painting Fine 180

240

320

Attaching/changing the sanding sheet on the sanding

plate

The sanding plate(10) is fitted with a hook-and-loop fasten-

ing, allowing sanding sheets with a hook-and-loop backing to

be secured quickly and easily.

Tap the hook-and-loop fastening of the sanding plate(10)

before fitting the sanding sheet(11) to facilitate maximum

adhesion.

Position the sanding sheet(11) so that it is flush with one

side of the sanding plate(10), then place the sanding sheet

on the sanding plate and press it on firmly.

To ensure optimum dust extraction, make sure that the

punched holes in the sanding sheet are aligned with the

drilled holes in the sanding plate.

To remove the sanding sheet(11), take hold of it by a corner

and pull it away from the sanding plate(10).

You can use all sanding sheets, polishing and cleaning

fleeces from the Delta 93mm series in Bosch’s range of ac-

cessories.

Sanding accessories such as fleece/polishing felt are at-

tached to the sanding plate in the same way.

Dust/chip extraction

The dust from materials such as lead paint, some types of

wood, minerals and metal can be harmful to human health.

Touching or breathing in this dust can trigger allergic reac-

tions and/or cause respiratory illnesses in the user or in

people in the near vicinity.

Certain dusts, such as oak or beech dust, are classified as

carcinogenic, especially in conjunction with wood treatment

additives (chromate, wood preservative). Materials contain-

ing asbestos may only be machined by specialists.

– Use a dust extraction system that is suitable for the ma-

terial wherever possible.

– Provide good ventilation at the workplace.

– It is advisable to wear a P2 filter class breathing mask.

The regulations on the material being machined that apply in

the country of use must be observed.

u Avoid dust accumulation at the workplace. Dust can

easily ignite.

Connecting the dust extraction system (see figure C)

The dust extraction system (17) is only designed for use

with the sanding plate (10); it serves no purpose when used

together with other application tools.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PMF 350 CES Multitool Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info