Bedienungsanleitung Bosch THB 1500 (Seite 9 von 56) (Deutsch, Englisch, Holländisch)

112553

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Use

Warning!

The Ironer must be fully lowered for

transportation!

❏ Put the shirt ironer in position.

❏ Turn lifting knob 1, Fig. 1, anti-clockwise

while gripping the button band, 8, Fig. 2,

with the other hand and pull it upwards.

Warning!

On releasing the lifting knob and pulling

the button band upwards, the appliance

rises to a specific height. Do not place

anything on top of the appliance during

this process!

❏ Grip the button band with both hands and

finish lifting the top 8, Fig. 2 part of the

appliance until you hear a click, which

indicates that it has reached its limit. Fig. 4.

❏ Plug it in.

For safety reasons, ironing and/or airing

can only be started when the upper frame

is completely raised.

The light flashes 10 times when the

lifted appliance is connected to the

electricity supply or when it is lifted from

its down position when already connected.

The light flashes to remind you to press

the button. Pressing the button initiates

preheating and thereby reduces drying

time.

Ironing

❏ Turn the collar adjuster knob 7, Fig. 2 to its

vertical position.

❏ Open all the flaps on the button band

adjuster and the collar support.

Fitting the shirt

❏ Unbutton the shirt and the cuffs.

❏ Lift the collar.

❏ Fit the damp, spin-dried shirt onto the

ironing dummy.

❏ Fit one arm of the ironing dummy inside the

shirtsleeve. Do not twist the sleeves, Fig. 5.

❏ Place the other arm of the ironing dummy

into the other shirtsleeve. Do not twist the

sleeves.

❏ The arrows shown in the picture indicate the

lower seam. Fig. 6.

❏ Line the lower hem up with the line marked

on the plastic part at the top of the button

band, Fig. 7

❏ Hold the collar flaps firmly and close the two

top flaps on the button band adjuster,

Fig. 8.

❏ Pull the button band on the shirt down and

fit it vertically onto the button band adjuster.

To avoid marking of any kind, do not insert

the button band too much. Position the

button band in such a way that the

perforated plate is completely covered.

❏ Starting at the top, close all the flaps on the

button band adjuster. Secure the button

band firmly in place. Close those flaps not

required to hold the shirt in place as well.

❏ Repeat this proceeding to tighten the other

side of the shirt.

❏ Turn the collar adjuster knob clockwise from

its vertical position while adapting the back

of the collar to the Ironer by pulling it gently

upwards with the other hand.

❏ Close the two upper supports on the casing

to maintain the shirt collar up. Correct the

positioning of the back of the shirt by pulling

it lightly upwards.

A spring adapts the collar adjuster to the

size of the shirt collar. The rotated position

of the knob depends on the size of the

shirt.

Do not overturn the knob when turning it

clockwise. The knob sets itself in the right

position.

Do not adjust the knob when the appliance

is inflated.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch THB 1500 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info