Bedienungsanleitung Bosch UniversalSaw 18V 70 (Seite 18 von 249) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

777032

Zoom out

Zoom in

Vorherige Seite

1/249

Nächste Seite

18 | English

Inserting/changing the saw blade

uWhen fitting or changing the saw blade, wear protect-

ive gloves. Blades are sharp and can become hot when

used for prolonged periods of time.

Selecting the saw blade

You will find an overview of recommended saw blades at the

end of these operating instructions. Only use saw blades

with a single lug shank (T shank) or with a 1/4" universal

shank (U shank). The saw blade should not be longer than

required for the intended cut.

Use a narrow saw blade when sawing tight curves.

Inserting the saw blade (seefigure A)

uClean the shaft on the saw blade before inserting it.

Adirty shaft cannot be securely fixed in place.

If necessary, remove the hood(8).

Push the saw blade receptacle (14) upwards in the direction

of the arrow. Push the saw blade (10), with the teeth in the

cutting direction, into the saw blade receptacle as far as it

will go.

Make sure when inserting the saw blade that the back of the

saw blade is in the groove on the guide roller (12).

uCheck that the saw blade is seated securely. A loose

saw blade can fall out and lead to injuries.

Removing the saw blade (seefigure B)

Push the saw blade receptacle (14) upwards in the direction

of the arrow and remove the saw blade (10).

Saw blade storage compartment (accessory) (see

figureC)

You can keep up to six saw blades that are no longer than

110mm in the saw blade storage compartment (16). Insert

the saw blades with single lug shank (T shank) into the saw

blade storage compartment in the recess intended for these.

You can place up to three saw blades on top of each other.

Close the saw blade storage compartment and push it as far

as it will go into the recess in the base plate (7).

Glide shoe (accessory) (seefigureD)

When machining sensitive surfaces, you can place the glide

shoe (17) on the base plate (7) in order to prevent the sur-

face from being scratched.

To position the glide shoe (17), hook it to the front of the

base plate (7), push it up at the back and allow it to click into

place.

When working with the glide shoe, neither the saw blade

storage compartment(16) nor the CutControlmust be

used.

Anti-splinter guard (accessory) (seefigureE)

The anti-splinter guard (18) (accessory) can prevent splin-

tering of the surface while sawing wood. The anti-splinter

guard can only be used with certain saw blade types and only

at a cutting angle of 0°. When sawing with the anti-splinter

guard, the base plate (7) must not be moved to the rear for

sawing close to edges.

Push the anti-splinter guard (18) into the base plate (7)

from below (as shown in the figure with the groove facing up-

wards).

CutControl (accessory)

CutControl enables the power tool to be guided precisely

along a cutting line marked on the workpiece. CutControl

includes the viewing window (11) with cut marks and the

base (9) for securing to the power tool.

Securing CutControl to the base plate (see figure F)

Firmly insert the viewing window for CutControl (11) into

the brackets on the base (9). Then push the base together

gently and allow it to click into place in the guide (19) on the

base plate (7).

Dust/Chip Extraction

The dust from materials such as lead paint, some types of

wood, minerals and metal can be harmful to human health.

Touching or breathing in this dust can trigger allergic reac-

tions and/or cause respiratory illnesses in the user or in

people in the near vicinity.

Certain dusts, such as oak or beech dust, are classified as

carcinogenic, especially in conjunction with wood treatment

additives (chromate, wood preservative). Materials contain-

ing asbestos may only be machined by specialists.

– Use a dust extraction system that is suitable for the ma-

terial wherever possible.

– Provide good ventilation at the workplace.

– It is advisable to wear a P2 filter class breathing mask.

The regulations on the material being machined that apply in

the country of use must be observed.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Hood (accessories) (see figuresGandH)

Fit the hood (8) before you connect the power tool to the

dust extraction system.

Position the hood (8) on the power tool so that the two outer

brackets engage in the recesses of the housing.

Remove the hood (8) when working without a dust extrac-

tion system and for mitre cuts. To do this, push the hood to-

gether at the level of the outer brackets and remove it by

pulling it forwards.

Connecting the dust extraction system (seefigureI)

Push the dust extraction adapter(20) (accessory) onto an

extraction hose(21) (accessory) until you hear it click into

place. Connect the dust extraction adapter(20) to the ex-

traction outlet(6) on the power tool and the extraction

hose(21) to a dust extractor (accessory).

You will find an overview of connecting to various dust ex-

tractors at the end of these operating instructions.

For optimum dust extraction, where possible use the anti-

splinter guard (18).

The dust extractor must be suitable for the material being

worked.

1 609 92A 64Y | (12.07.2021) Bosch Power Tools

Bosch UniversalSaw 18V 70 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info