Bedienungsanleitung Bresser Messier Exos 1 (Seite 11 von 44) (Englisch)

784594

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Assembling

(EXOS-1/EXOS-2 mount on ST-2 tripod)

Telescope Assembly

As you unpack your telescope, carefully note the following parts. The

assembly is shipped in separate boxes.

• Equatorial mount with polar alignment finder

• Heavy duty, adjustable steel tube tripod with leg braces, three tripod leg

lock knobs, and a captive mount locking knob

• Optical tube assembly, dust cover, focuser, eyepiece holder, tube cradle

assembly and fixing screws

• Eyepiece

• Diagonal prism (only for AR models)

• Counterweight and counterweight shaft

• 8x50 / 6x30mm viewfinder

How to Assemble Your Telescope

The giftboxes contain the optical tube assembly and its components, the

tripod with the equatorial mount and the accessories.

1. Remove the components from the packaging and familiarise yourself

with them. Please refer to illustrations 1a to 1d for details of telescope

assembly. When removing the tripod from its packaging keep it parallel

to the floor as the inner legs may otherwise slide out as they are not yet

screwed tight.

2. Locking the tripod legs. Spread the legs until the spider vanes of the

accessory plate are tautened (illustration. 3).

3. Fastening the spacing plate in place. To fasten the central screw (illustra-

tion 4, A) on the tripod first screw the tensioning screw (illustration 4, B)

on. This can be screwed right down as it serves to clamp the spacing

plate against the tripod legs. You can now insert the plate (illustration 4,

C) from above on the central screw. Make sure the plate bars (illustration

4, D) show downwards.

Attention:

It‘s important the following step is applied to avoid any damage to the

thread.

To prevent the threaded rod (illustration 4, E) being screwed into the mount

too far use the gapping washer (illustration 4, F) supplied. Insert it from

above on the threaded rod so that the wider chamfered side shows down-

wards. The spacing ring must be on the threaded rod „step“. Now push the

threaded rod from below through the tripod base and slide the C-clip (illus-

tration 4a, A) on the recess (illustration 4a, B) in the threaded rod

4. Fastening the mount on the tripod head. Place the mounting on the

tripod head. Make sure the projection on the tripod is between the azi-

muth adjustment screws (illustration 5). To do so first loosen the azimuth

screws sufficiently to allow space for the projection. Place the mounting

on the tripod top in such a way that the projecting cylinder on the base

fits into the hole in the tripod base centre and fasten it in place using the

central screw. Tighten the screw hand tight.

5. Fastening the counterweight on the counterweight rod: insert the base

of the counterweight rod (20, illustration 1d) on the threaded end of the

rod and screw it on the counterweight rod (22, illustration 1). Then screw

both in the thread on the base of the declination axis and counter screw

rod to base. If you look through the large drill hole in the counterweight

Looking at or near the Sun will cause instant and irreversible damage to your eye!

assemblInG exos-2

Fig. 3: The tripod

Fig. 5: installing the mounting on

the tripod.

Fig. 4: Fastening the spacing plate

and distance washer in place.

Fig. 4a: Threaded rod fastening

using the C-clip

Gudgeon Azimuth

fine adjust-

ment

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser Messier Exos 1 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bresser Messier Exos 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info