Bedienungsanleitung Bresser Messier Exos 1 (Seite 13 von 44) (Englisch)

784594

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

NOTE:

Two eyepiece holders are included with your EXOS-2-NT-telescope - for both 1.25”

and 2” eyepieces. To change eyepiece holders, unscrew the attached holder from

the focuser and thread on the other holder.

11. Adjust the height of the tripod: Adjust the height of the tripod by

loosening the tripod lock knobs (Fig. 11). Extend the sliding inner

section of each tripod leg to the desired length; then tighten each knob.

Adjust the tripod to a height that is comfortable for viewing.

13. Remove Plastic from Reticle LED*: The polar alignment reticle LED

(30, Fig. 1d) contains two watch batteries. The reticle‘s LED is shipped

with a plastic strip between the two batteries to protect battery life.

Unthread both the thumbscrew (F) and the threaded lid (E). Remove

the plastic strip before using. Refer to the reticle assembly in Fig. 13b

and note the orientation of the batteries. Place the batteries (C) into

the battery holder (D) before inserting into the reticle container (A).

Getting Started! – First Steps

Balancing the Telescope

In order for the telescope to be stable on the tripod and also for it to move

smoothly, it must be balanced. To balance the telescope, unlock the Right

Ascension or R.A. lock (33, Fig. 1d). When this axis is unlocked, the tel-

escope pivots on the R.A. axis. Later in the procedure, you will also unlock

the Declination or Dec. lock (17, Fig. 1d). When unlocked, the telescope

pivots on the Dec. axis. Most of the motion of the telescope takes place by

moving about these two axes, separately or simultaneously. Try to become

familiar with these locks and observe how the telescope moves on each

axis. To obtain a fine balance of the telescope, follow the method below:

1. Firmly hold the optical tube secure so that it cannot accidentally

swing freely. Loosen the R.A. lock (33, Fig. 1d). The optical tube now

moves freely about the R.A. axis. Rotate the telescope so that the

counterweight shaft is parallel (horizontal) to the ground.

2. Unlock the counterweight lock knob and slide the counterweight (21,

Fig. 1d) along the counterweight shaft until the telescope remains in one

position without tending to drift down in either direction. Then re-tighten

the counterweight lock knob, locking the counterweight in position.

3. Again, hold the optical tube so that it cannot accidentally swing freely.

Lock the R.A. lock (33, Fig. 1d), and unlock the Dec. lock (17, Fig. 1d).

The telescope now is able to move freely about the Dec. axis. Loosen

the cradle ring lock knobs (13, Fig. 1a) so that the main tube slides eas-

ily back and forth in the cradle rings. Move the main tube in the cradle.

Looking at or near the Sun will cause instant and irreversible damage to your eye!

fIrst steps

Fig. 10b: Insert eyepiece into

diagonal prism and tighten

thumbscrews.

Fig. 10a: Insert eyepiece intor hol-

der and tighten thumbscrews.

Fig. 11: Adjust the tripod height

using the leg lock knobs.

Leg lock knob

* Optional accessory for EXOS-2

Eyepiece

Holder

Thumbscrews

Diagonal

prism

Sucher

Eyepiece

Holder

Thumbscrew NT

Viewfinder

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser Messier Exos 1 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bresser Messier Exos 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info