613636
77
Zoom out
Zoom in
Vorherige Seite
1/88
Nächste Seite
Troubleshooting 75
3
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
The upper thread
breaks.
The thread is tangled, for example,
in the bobbin case.
Remove the tangled thread. If the
thread is tangled in the bobbin case,
clean the race.
page 70
The needle is bent or blunt. Replace the needle.
page 35
The needle is incorrectly installed. Correctly install the needle.
The area around the hole in the
needle plate is scratched, or has a
burr on it.
Replace the needle plate. Contact
your retailer or the nearest authorized
service center.
The area around the hole in the
embroidery foot is scratched, or
has a burr on it.
Replace the embroidery foot. Contact
your retailer or the nearest authorized
service center.
The bobbin case is scratched, or
has a burr on it.
Replace the bobbin case. Contact
your retailer or the nearest authorized
service center.
A bobbin designed specifically for
this machine is not used.
Incorrect bobbins will not work
properly. Only use a bobbin
designed specifically for this
machine.
page 24
Bobbin thread
does not wind
neatly on the
bobbin.
The thread that was pulled out
was not wound onto the bobbin
correctly.
Wind the thread that was pulled off
around the bobbin five or six times
clockwise.
page 26
The lower thread
is tangled or
breaks.
The bobbin thread is incorrectly
installed.
Correctly install the bobbin thread. page 28
The bobbin is scratched or does
not rotate smoothly, or has a burr
on it.
Replace the bobbin.
The thread is tangled.
Remove the tangled thread and clean
the race.
page 70
A bobbin designed specifically for
this machine is not used.
Incorrect bobbins will not work
properly. Only use a bobbin
designed specifically for this
machine.
page 24
The thread tension
is incorrect.
The upper thread was not
threaded correctly.
Correct the upper threading. page 30
The bobbin thread is incorrectly
installed.
Correctly install the bobbin thread. page 28
The thread tension is incorrect.
Adjust the tension of the upper
thread.
page 64
A bobbin designed specifically for
this machine is not used.
Incorrect bobbins will not work
properly. Only use a bobbin
designed specifically for this
machine.
page 24
Symptom Probable Cause Remedy Reference
77

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Brother Innov-is 700E II wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Brother Innov-is 700E II

Brother Innov-is 700E II Kurzanleitung - Deutsch - 24 seiten

Brother Innov-is 700E II Bedienungsanleitung - Deutsch - 88 seiten

Brother Innov-is 700E II Kurzanleitung - Englisch, Holländisch - 24 seiten

Brother Innov-is 700E II Bedienungsanleitung - Holländisch - 88 seiten

Brother Innov-is 700E II Kurzanleitung - Französisch - 24 seiten

Brother Innov-is 700E II Bedienungsanleitung - Französisch - 88 seiten

Brother Innov-is 700E II Kurzanleitung - Italienisch, Spanisch - 24 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info