613636
78
Zoom out
Zoom in
Vorherige Seite
1/88
Nächste Seite
76
APPENDIX — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
Stitches are
skipped.
The upper thread was not
threaded correctly.
Correct the upper threading. page 30
The needle is bent or blunt. Replace the needle. page 35
The needle is incorrectly installed. Correctly install the needle. page 36
Dust has accumulated under the
needle plate or in the bobbin case.
Remove the needle plate cover and
clean the race.
page 70
A high-pitched
noise is made
while
embroidering.
Dust has accumulated in the
bobbin case.
Clean the race. page 70
The upper thread was not
threaded correctly.
Correct the upper threading. page 30
The bobbin case is scratched, or
has a burr on it.
Replace the bobbin case. Contact
your retailer or the nearest authorized
service center.
A bobbin designed specifically for
this machine is not used.
Incorrect bobbins will not work
properly. Only use a bobbin
designed specifically for this
machine.
page 24
The thread does
not pass through
the eye of the
needle.
The needle has not been raised to
the correct position.
Press the needle position button. page 32
The needle is incorrectly installed. Correctly install the needle. page 36
The stitch is not
sewn correctly.
The thread tension is incorrect.
Adjust the tension of the upper
thread.
page 64
The thread is tangled, for example,
in the bobbin case.
Remove the tangle thread. If the
thread is tangled in the bobbin case,
clean the race.
page 70
The lamps do not
come on.
The lamps are damaged.
Contact your retailer or the nearest
authorized service center.
The machine is not turned on. Turn on the machine. page 19
Nothing appears
on the LCD.
The brightness of the LCD is either
too light or too dark.
Adjust the brightness of the LCD. page 81
Machine does not
operate when
button is pressed.
An animation is displayed on the
LCD.
Touch the LCD with your finger, and
the animation will disappear.
page 20
Embroidery unit
does not move.
No pattern selected. Select a pattern. page 49
The embroidery unit is not set up
correctly.
Set up the embroidery unit correctly. page 15
Embroidering
continues
although the
bobbin thread
ran out.
Dust has collected on the bobbin
thread sensor.
Remove any dust from the bobbin
thread sensor.
page 70
Symptom Probable Cause Remedy Reference
78

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Brother Innov-is 700E II wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Brother Innov-is 700E II

Brother Innov-is 700E II Kurzanleitung - Deutsch - 24 seiten

Brother Innov-is 700E II Bedienungsanleitung - Deutsch - 88 seiten

Brother Innov-is 700E II Kurzanleitung - Englisch, Holländisch - 24 seiten

Brother Innov-is 700E II Bedienungsanleitung - Holländisch - 88 seiten

Brother Innov-is 700E II Kurzanleitung - Französisch - 24 seiten

Brother Innov-is 700E II Bedienungsanleitung - Französisch - 88 seiten

Brother Innov-is 700E II Kurzanleitung - Italienisch, Spanisch - 24 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info