Bedienungsanleitung Brother Innov-is XP1 (Seite 189 von 204) (Englisch)

718773

189

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

TROUBLESHOOTING

187

Appendix

■ While embroidering

Nothing happens,

even if the LCD

display is pressed

The screen has been locked. Press either of the following keys to unlock the

screen.

—

The LCD screen is

fogged up.

Condensation has formed on the LCD screen. After a while, the cloudiness will disappear.

—

Embroidery unit does

not operate.

Embroidery unit is not attached correctly. Reattach the embroidery unit correctly.

Embroidery frame was attached before the

unit was initialized.

Remove the embroidery unit, and then perform

the initialization process correctly.

Pointer of the

projector does not

indicate the position

correctly

With thick elastic fabric, the position will be

misaligned only at raised parts in the fabric.

Manually adjust the position according to the

thickness of the fabric.

With fabric having a very uneven surface, the

position is not correctly aligned.

The pointer indication should be used only as

a reference.

—

Problem Cause Solution Page

Machine does not

operate.

“Start/Stop” button was not pressed. Press the “Start/Stop” button.

—

There is no pattern selected. Select a pattern.

Embroidery foot is not lowered. Lower the embroidery foot.

—

Needle breaks. Needle is installed incorrectly. Reinstall the needle correctly. 11

Needle clamp screw is not tightened. Tighten the needle clamp screw. 12

Needle is turned or bent. Replace the needle. 11

Using improper needle or thread for the

selected fabric.

Refer to the “Fabric/Thread/Needle

Combinations” chart in the Operation Manual

(Sewing).

—

Wrong embroidery foot was used. Use the recommended embroidery foot.

Upper thread tension is too tight. Adjust the thread tension. 102

Fabric is pulled during embroidering. Do not pull the fabric during embroidering. —

Spool cap is set incorrectly. Check the method for attaching the spool cap,

then reattach the spool cap.

There are scratches around the opening in the

needle plate.

Replace the needle plate, or consult your

authorized Brother dealer.

—

There are scratches around the opening in the

embroidery foot.

Replace the embroidery foot, or consult your

authorized Brother dealer.

There are scratches on the bobbin case. Replace the bobbin case, or consult your

authorized Brother dealer.

—

Needle is defective. Replace the needle. 11

A bobbin designed specifically for this

machine is not used.

Incorrect bobbins will not work properly. Only

use a bobbin designed specifically for this

machine.

Upper threading is incorrect. Check the steps for threading the machine and

rethread the machine.

Bobbin is set incorrectly. Reset the bobbin thread correctly. 20

Embroidery foot is attached incorrectly. Attach the embroidery foot correctly. 9

Screw of the presser foot holder is loose. Securely tighten the screw of the presser foot.

Fabric is too thick. Use fabric that the needle can pierce when the

handwheel is turned.

—

Stabilizer is not attached to fabric being

embroidered.

Attach stabilizer. 28

Bobbin thread is incorrectly wound. Use a correctly wound bobbin. 15

Problem Cause Solution Page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother Innov-is XP1 Seite 189

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother Innov-is XP1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info