Bedienungsanleitung Brother Innov-is XP1 (Seite 191 von 204) (Englisch)

718773

191

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

TROUBLESHOOTING

189

Appendix

Skipped stitches Machine is threaded incorrectly. Check the steps for threading the machine and

rethread it correctly.

Using improper needle or thread for the

selected fabric.

Refer to the “Fabric/Thread/Needle

Combinations” chart in the Operation Manual

(Sewing).

—

Needle is turned, bent or the point is dull. Replace the needle. 11

Needle is installed incorrectly. Reinstall the needle correctly. 11

Needle is defective. Replace the needle. 11

Dust or lint has collected under the needle

plate.

Remove the dust or lint with the brush. —

High-pitched sound

while embroidering

Pieces of thread are caught in the race. Clean the race. —

Upper threading is incorrect. Check the steps for threading the machine and

rethread the machine.

A bobbin designed specifically for this

machine is not used.

Incorrect bobbins will not work properly. Only

use a bobbin designed specifically for this

machine.

There are needle holes or friction scratches in

the bobbin case.

Replace the bobbin case, or consult your

authorized Brother dealer.

—

Fabric does not feed

through the machine.

Needle is turned, bent or the point is dull. Replace the needle. 11

Thread is entangled. Cut the entangled thread and remove it from

the race.

—

The fabric feeds in

the opposite

direction.

The feed mechanism is damaged. Contact your authorized Brother dealer.

—

The needle contacts

the needle plate.

The needle clamp screw is loose. Firmly tighten the needle clamp screw. If the

needle is bent or blunt, replace it with a new

one.

Needle is turned, bent or the point is dull. Replace the needle. 11

Fabric being

embroidered with the

machine cannot be

removed.

Thread is tangled below the needle plate. Lift up the fabric and cut the threads below it,

and clean the race.

—

A broken needle has

fallen into the

machine.

— Turn off the machine, and then remove the

needle plate. If the needle that fell into the

machine can be seen, use tweezers to remove

it. After removing the needle, return the needle

plate to its original position.

Before turning on the machine, slowly turn the

handwheel toward you to check that it turns

smoothly. If the handwheel does not turn

smoothly or the needle that fell into the

machine cannot be removed, consult your

authorized Brother dealer.

—

The handwheel feels

sluggish when it is

turned.

Thread is tangled in the bobbin case. Remove the tangled thread from the bobbin

case. Re-install the bobbin case so it is

correctly positioned.

—

The machine does

not detect the

embroidery

positioning sticker.

Sunlight or light from the outside comes into

the machine.

Block light from the outside. —

The scanned image is

too bright or too pale.

Problem Cause Solution Page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother Innov-is XP1 Seite 191

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother Innov-is XP1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info