Bedienungsanleitung Brother Innov-is XP1 (Seite 192 von 204) (Englisch)

718773

192

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

TROUBLESHOOTING

190

■ After embroidering

Problem Cause Solution Page

Thread tension is

incorrect.

Upper threading is incorrect. Check the steps for threading the machine and

rethread the machine.

Bobbin is set incorrectly. Reset the bobbin. (If needle plate was

removed, reinstall needle plate.)

Using improper needle or thread for the

selected fabric.

Refer to the “Fabric/Thread/Needle

Combinations” chart in the Operation Manual

(Sewing).

—

Thread tension is set incorrectly. Adjust the thread tension. 102

Bobbin thread is incorrectly wound. Use a correctly wound bobbin. 15

Needle is turned, bent or the point is dull. Replace the needle. 11

A bobbin designed specifically for this

machine is not used.

Incorrect bobbins will not work properly. Only

use a bobbin designed specifically for this

machine.

Embroidery pattern

does not embroider

out correctly.

Thread is twisted. Use scissors, etc., to cut the twisted thread

and remove it from the bobbin case, etc.

—

Thread tension is set incorrectly. Adjust the thread tension. 102

Fabric was not inserted into the frame

correctly (fabric was loose, etc.).

If the fabric is not stretched tight in the frame,

the pattern may turn out poorly or there may

be shrinkage of the pattern. Set the fabric into

the frame correctly.

Stabilizing material was not attached. Always use stabilizing material, especially with

stretch fabrics, lightweight fabrics, fabrics with

a coarse weave, or fabrics that often cause

pattern shrinkage. See your authorized Brother

dealer for the proper stabilizer.

There was an object placed near the machine,

and the carriage or embroidery frame hit the

object during embroidering.

If the frame bumps something during

embroidering, the pattern will turn out poorly.

Do not place anything in the area where the

frame may bump it during embroidering.

Fabric outside the frame edges interferes with

the free arm, so the embroidery unit cannot

move.

Reinsert the fabric in the embroidery frame so

that the excess fabric is away from the free

arm, and rotate the pattern 180 degrees.

Fabric is too heavy, so the embroidery unit

cannot move freely.

Place a large thick book or similar object under

the arm head to lightly lift the heavy side and

keep it level.

—

Fabric is hanging off the table. If the fabric is hanging off the table during

embroidery, the embroidery unit will not move

freely. Place the fabric so that it does not hang

off the table or hold the fabric to keep it from

dragging.

Fabric is snagged or caught on something. Stop the machine and place the fabric so that

it does not get caught or snagged.

—

Embroidery frame was removed during

embroidering (for example, to reset the

bobbin). The embroidery foot was bumped or

moved while removing or attaching the

embroidery frame, or the embroidery unit was

moved.

If the embroidery foot is bumped or the

embroidery unit is moved during embroidering,

the pattern will not turn out. Be careful when

removing or reattaching the embroidery frame

during embroidering.

Stabilizer is incorrectly attached, for example,

it is smaller than the embroidery frame.

Attach the stabilizer correctly. 28

Loops appear on the

surface of the fabric

when embroidering

The thread tension is incorrectly set. Adjust the thread tension.

102

The tension of the upper thread is incorrectly

set for the combination of the fabric, thread

and pattern being used.

Use the embroidery needle plate cover.

The combination of the bobbin case and

bobbin thread is incorrect.

Change the bobbin case or bobbin thread so

that the correct combination is used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother Innov-is XP1 Seite 192

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother Innov-is XP1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info