Bedienungsanleitung Brother Innov-is XP1 (Seite 190 von 204) (Englisch)

718773

190

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

TROUBLESHOOTING

188

Upper thread breaks. Machine is not threaded correctly (used the

wrong spool cap, spool cap is loose, the

thread did not catch the needle bar threader,

etc.)

Rethread the machine correctly. 22

Knotted or tangled thread is being used. Remove any knots or tangles.

—

The selected needle is not appropriate for the

thread being used.

Refer to the “Fabric/Thread/Needle

Combinations” chart in the Operation Manual

(Sewing).

—

Upper thread tension is too tight. Adjust the thread tension. 102

Thread is twisted. Use scissors, etc., to cut the twisted thread

and remove it from the race, etc.

—

Needle is turned, bent or the point is dull. Replace the needle. 11

Needle is installed incorrectly. Reinstall the needle correctly. 11

There are scratches around the opening of the

needle plate.

Replace the needle plate, or consult your

authorized Brother dealer.

—

There are scratches around the opening in the

embroidery foot.

Replace the embroidery foot, or consult your

authorized Brother dealer.

There are scratches on the bobbin case. Replace the bobbin case, or consult your

authorized Brother dealer.

—

Using improper needle or thread for the

selected fabric.

Refer to the “Fabric/Thread/Needle

Combinations” chart in the Operation Manual

(Sewing).

—

While embroidering, the thread became

knotted or tangled.

Rethread upper and lower thread. 20, 22

A bobbin designed specifically for this

machine is not used.

Incorrect bobbins will not work properly. Only

use a bobbin designed specifically for this

machine.

The thread is tangled

on the wrong side of

the fabric.

Upper threading is incorrect. Check the steps for threading the machine and

rethread the machine. Be sure that the

embroidery foot is in the raised position when

threading the machine so that the upper

thread sets properly in the upper tension.

Using improper needle or thread for the

selected fabric.

Refer to the “Fabric/Thread/Needle

Combinations” chart in the Operation Manual

(Sewing).

—

The upper thread is

too tight.

The bobbin thread is incorrectly installed. Correctly install the bobbin thread. 20

Bobbin thread

breaks.

Bobbin is set incorrectly. Reset the bobbin thread correctly. 20

Bobbin thread is incorrectly wound. Use a correctly wound bobbin. 15

There are scratches on the bobbin or it doesn’t

rotate properly.

Replace the bobbin. 20

Thread is twisted. Use scissors, etc. to cut the twisted thread

and remove it from the race, etc.

—

A bobbin designed specifically for this

machine is not used.

Incorrect bobbins will not work properly. Only

use a bobbin designed specifically for this

machine.

Fabric puckers. There is a mistake in the upper or bobbin

threading.

Check the steps for threading the machine and

rethread it correctly.

20, 22

Spool cap is set incorrectly. Check the method for attaching the spool cap,

then reattach the spool cap.

Using improper needle or thread for the

selected fabric.

Refer to the “Fabric/Thread/Needle

Combinations” chart in the Operation Manual

(Sewing).

—

Needle is turned, bent or the point is dull. Replace the needle. 11

Thread tension is set incorrectly. Adjust the thread tension. 102

Problem Cause Solution Page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother Innov-is XP1 Seite 190

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother Innov-is XP1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info