Bedienungsanleitung Cambridge Audio AZUR 851D (Seite 5 von 16) (Englisch)

656745

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Rear panel connections

Power On/Off

Switches the unit on and off.

This product has APD (Auto Power Down) enabled as default. After

inactivity of 30 minutes, the product will automatically switch to Standby.

See later section for further details.

AC power socket

Once you have completed all connections to the DAC, plug the AC power

cable into an appropriate mains socket then switch on. Your unit is now

ready for use.

Mains Voltage Selector Switch (CU version only)

Switches the 851D mains voltage between 100V and 115V.

Note: Intended for use by a professional installer or Cambridge Audio

retailer only.

RS232C

The RS232C port allows external serial control of the 851D for custom

install use. A full command set is available on the Cambridge Audio

website at www.cambridge-audio.com. This port can also be used by

Cambridge Audio service personnel for software updates.

IR (Infrared) Emitter In

Allows modulated IR commands from multi-room systems to be

received by the amplier. Commands received here are not looped out

of the Control Bus. Refer to the 'Custom installation' section for more

information.

Trigger Out

This 12V trigger output can be used to control external devices such as

an 851W or another power amplier, or a subwoofer, projector, screen

etc. See later section for further details.

Control Bus

In - Allows un-modulated commands from multi-rooms systems or other

components to be received by the unit.

Out - Loop out for control bus commands to another unit. Also allows the

851D to control some Cambridge Audio units.

BT100/Ext.

The optional Cambridge Audio BT100 Bluetooth Adaptor can be plugged

in here adding wireless streaming audio capability directly from most

phones, tablets and laptops. Will also be use for planned optional future

wireless modules. Can also be use for charging devices up to 500mA.

See later section for details.

Digital Outputs

The 851D digital outputs allow connection to a separate DAC (digital to

analogue converter) or can be used to loop the selected signal through

to an AVR.

Note: These outputs pass through the currently selected audio source

un-processed, i.e. no volume control or up-sampling is performed on the

digital outputs.

Coaxial – To obtain best results, use a high quality 75 ohm digital RCA

interconnect cable (not one designed for normal audio use).

Toslink Optical – Use a high quality TOSLINK bre optic interconnect

cable designed specically for audio use.

USB Interface

A USB B type socket is tted to the 851D to enable the playback of audio

from a personal computer running either Microsoft Windows or Apple

Mac OS X operating systems. Some builds of Linux are also suitable.

Note: Always use a high quality USB connection cable certied as USB Hi-

Speed. USB cable connections longer than 3m may result in inconsistent

audio performance.

Always turn the Volume to minimum, switch to another

input or turn the 851D off before plugging/unplugging

cables to the USB input or whilst booting up/shutting

down your PC/Mac.

Ground Lift Switch

The Ground Lift Switch enables the USB interface earth to be

disconnected from the 851D chassis earth. Disconnecting (lifting) the

earth can be useful if electronic hum is heard through the speakers

when the USB input is selected. The switch should otherwise be left in

the Ground position.

Digital Inputs 1 – 6

The 851D has 6 digital inputs in total. Inputs 1 and 2 feature both S/

PDIF co-axial and Toslink optical sockets. You can use whichever is most

convenient, but not both at the same time. Inputs 3 and 4 feature Toslink

optical sockets only. Input 5 features BNC co-axial socket and input 6

features a AES/EBU Balanced socket.

Coaxial – Use a high quality 75 ohm digital RCA Phono interconnect

cable (not one designed for normal audio use). This input is suitable for

16-24 bit content up to 192kHz.

Toslink Optical – Use a high quality TOSLINK bre optic interconnect

cable designed specically for audio use. This input is suitable for 16-24

bit content up to 96kHz (Toslink is not recommened at 192kHz sampling

rates).

BNC Coaxial – Use a high quality 75 ohm digital RCA Phono interconnect

cable (not one designed for normal audio use). This input is suitable for

16-24 bit content up to 192kHz. If required, a BNC to RCA coaxial adaptor

or a BNC to RCA coaxial cable can be used to provide connectivity to a

third S/PDIF coaxial digital input source

AES/EBU – For sources with a balanced (AES/EBU) digital output. This

input is suitable for 16-24 bit content up to 192kHz.

851Dazur

ENGLISH

1312

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cambridge Audio AZUR 851D Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge Audio AZUR 851D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info