Bedienungsanleitung Cambridge Audio AZUR 851D (Seite 6 von 16) (Englisch)

656745

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Rear panel connections cont.

Unbalanced Audio Output

A conventional RCA phono stereo output for connection to the line-level

inputs of an amplier. Use a high quality stereo RCA phono interconnect

cable intended for analogue audio signals.

Balanced Audio Output

The 851D features balanced outputs on two XLR sockets. Balanced

outputs provide slightly better audio performance and can reject cable-

borne noise and interference when used with equipment with balanced

inputs.

Note: XLR connectors should be wired as follows:

Pin 1: Ground

Pin 2: Hot (in-phase)

Pin 3: Cold (phase-inverted)

Front panel controls

44.1kHz

Input 1

Input 2

Input 3

Input 4

BNC

AES/EBU

BTooth

USB

Standby/On

Switches the unit between Standby mode (indicated by dim power LED)

and On (indicated by bright power LED). Standby is a low power mode

where the power consumption is less than 0.5 Watts. The unit can be left

in Standby mode when not in use.

Headphone connection

Allows for the connection of headphones with a ¼" jack plug connector.

Note: 600 Ohm headphones will work well on the 851D. However, with

some less sensitive models maximum volume maybe limited. If louder

listening is required, a lower impedance / higher sensitivity set of

headphones is recommended.

Press to enter the 851D's setup menus. Various 851D operating

parameters can be congured. Refer to the 'Operating instructions'

section for more information.

Filter

The different digital lters can be selected from the 851D’s setup

menu. Alternatively, pressing the Filter/

ø button on the remote will cycle

through different digital lter phase modes: Linear, Minimum, Steep,

Linear inverted, Minimum inverted and Steep inverted. Alternative digital

lters can offer subtly different sound quality characteristics. See later

section for further details. The currently selected lter is displayed by the

indicators just above the button.

Phase

Press the Filter button on the remote to cycle through different phase

output.

If you suspect that your source material or amplier, etc., is inverting the

phase of the musical signal, you can use this function to re-invert the

audio and regain absolute positive phase by pressing the phase button

in the setup menu. Alternatively, to select using the remote control, cycle

through the modes as described above.

Infrared sensor

Receives IR commands from the supplied Azur remote control. A clear

unobstructed line of sight between the remote control and the sensor

is required.

Source select buttons

Push the appropriate input selection button to select the source

component that you wish to listen to (highlighted by a solid circle on the

display).

Display

LCD used to control the 851D. Please refer to the 'Operating instructions'

and 'Settings' section of this manual for more information.

Volume

When Pre-amp mode is enabled, use to increase/decrease the level of

the sound from the outputs of the pre-amplier. This control affects the

level of the analogue audio output, and the headphones output. It does

not affect the digital output connections

Please refer to the 'Operating instructions' section of this manual for

more information on some of the functions of these buttons.

1 2 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cambridge Audio AZUR 851D Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge Audio AZUR 851D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info