Bedienungsanleitung Canadian Spa Company Toronto SE (Seite 8 von 24) (Englisch)

764895

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

TORONTO SE

Filling up your Spa

IMPORTANT: Before lling the spa, it is important to read and

understand the water chemistry section of this manual. Do not

proceed until the water chemistry section is understood and the

source water is tested.

Verify that the spa is in the desired nal location. Refer to the

‘Choose your location’ section - once lled, the spa cannot be

moved without draining.

Follow these lling instructions to avoid damage to the spa

pumps:

1. Leave power to the spa off until spa is completely lled.

2. Never leave an unlled spa exposed to direct sunlight with

out the Spa Cover installed. Resulting damage such as

bubbles and wrinkles in the spa shell and fading of the jet

faces is not covered by the manufacturer’s warranty.

3. Never operate spa pump without water because this could

result in permanent pump and/or heater damage which is

not covered by the manufacturer’s warranty.

4. Remove all warning labels from spa shell.

6. Remove the lter lid, basket and lter cartridge.

7. Inspect all Jets (shipping may cause jets to become loose

or detached). Check to see that the black Drain Valve

(located to the left or right of the front access panel) is closed.

IMPORTANT: Follow the next steps closely to prevent damage

to the Spa Pump.

Filter Type: Glacier Microban Filter Set SKU: KA-10032

8. Insert garden hose or other clean water source directly into

lter housing. Push hose pipe into lter housing until it

stops. Fill up to middle of the skimmer. Secure hose

placement and turn on water. Filling the spa through the

lter housing prevents an air lock from occurring in the spa

pumps, which is an air pocket preventing the ow of

water through the pump. Permanent damage caused by

running the pump with an air lock (or without water) is not

covered by the manufacturer’s warranty.

9. Check for leaks! Although spas are fully checked at the

factory, shipping and delivery might cause a leak.

10. Before power is applied familiarise yourself with the spa

control operations.

11. Turn water off and remove hose.

12. Reinstall lter cartridge, basket and lter lid.

13. Add start-up Chemicals after power is turned on.

Draining your Spa/Using the drain valve

1. Start by shutting off the electrical breaker connected to

your spa.

2. Locate the drain valve at the side of the spa. This valve has

a straightforward locking mechanism that stops the water

from owing out while you attach a garden hose to the cap.

First using the tab of the cap pull and twist until the pipe

comes out.

Then with the pipe out turn clockwise until the pipe extends

further out.

3. With the valve fully extended, unscrew the cap from the

middle of the valve.

4. Screw in the male end of the garden hose to the valve and

run the hose to your drain location.

5. Once the water has stopped owing out of the drain valve,

use the wet/dry vacuum to suck out any remaining water

from each jet head.

6. Twist valve and push in to CLOSE.

Accessing your spa controls

(8)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canadian Spa Company Toronto SE Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info