Bedienungsanleitung Canon Pixma MP 990 series (Seite 1056 von 1086) (Englisch)

542776

1056

Zoom out

Zoom in

Vorherige Seite

1/1086

Nächste Seite

Check 1: Make sure that the machine is turned on.

Check 2: Is Change wireless/wired in Device settings set to Wireless LAN active

or Wired LAN active?

Changing the Machine Settings on the LCD

Check 3: When using wired LAN, make sure that the LAN cable is connected

properly.

Check 4: When using wireless LAN, make sure that the network settings in the

machine are identical with those of the access point.

Refer to the manual provided with the access point or contact its manufacturer to check the

access point settings, and then modify the machine settings.

How to Set a WEP/WPA/WPA2 Key

Check 5: When using wireless LAN, make sure that the machine is not place as

far away from the access point.

The access point is located indoors within the effective range for wireless communication.

Locate the machine within 50 m from the access point.

Check 6: When using wireless LAN, make sure that there is no obstruction.

Wireless communication between different rooms or floors is generally poor. Adjust the

location of the devices.

Check 7: When using wireless LAN, make sure that there is no source of radio

wave interference in your vicinity.

There may be a device such as a microwave oven using the same frequency bandwidth as

the wireless station. Place the wireless devices as far away from the interference source as

possible.

Check 8: Make sure that the network settings of the computer are correct.

For the procedures to connect a network device to the computer and set them up, refer to the

manual of your network device or contact its manufacturer.

Check 9: Make sure that the radio status is good and adjust the installation

positions while monitoring the radio status with Canon IJ Network Tool.

Monitoring Wireless Network Status

Check 10: Make sure that the valid wireless channel is used.

The wireless channel to be used may be limited depending on wireless network devices

installed in the computer. Refer to the manual provided with your computer or your wireless

network device to specify the valid wireless channel.

Check 11: Make sure that the channel set to the access point is valid to

communicate with the computer, confirmed in Check 10.

If not, change the channel set to the access point.

Check 12: Make sure that the firewall of the security software is disabled.

If the firewall function of your security software is turned on, a message may appear warning

that Canon software is attempting to access the network. If the warning message appears,

set the security software to always allow access.

If using any programs that switch the network environment, check their settings. Some

programs will enable a firewall by default.

Check 13: When using a router, connect the printer and computer to the LAN

side (same network segment).

For placement:

When using wireless LAN, make sure that there is no barrier or obstacle between the access

Page 1056 of 1086 pagesCannot Communicate With the Machine/Cannot Print from the Machine

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon Pixma MP 990 series Seite 1056

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canon Pixma MP 990 series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info