Bedienungsanleitung Casio 3134 (Seite 13 von 15) (Englisch)

466632

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

Operation Guide 3134 3205

Moon Phase Indicator

The Moon phase indicator of this watch indicates

the current phase of the Moon as shown below. It

is based on the view of the left side of the moon

at meridian transit from the northern hemisphere

of the Earth. If the appearance of the Moon

phase indicator is reversed from the actual Moon

as viewed from your location, you can use the

procedure under “To reverse the displayed Moon

phase” to change the indicator.

Moon Phase indicator

Module 3134 Module 3205

Moon phase

(part you can see)

(part you cannot see)

Moon

Phase

Indicator

New Moon

First Quarter (Waxing)

28.7-29.5

1.0-2.7 2.8-4.6 4.7-6.4 6.5-8.3

8.4-10.1

10.2-12.0 12.1-13.8

0.0-0.9

Module

3134

Module

3205

Moon Age

Moon Phase

13.9-15.7 15.8-17.5 17.6-19.4 19.5-21.2 21.3-23.1 23.2-24.9 25.0-26.8 26.9-28.6

Moon

Phase

Indicator

Full Moon

Last Quarter (Waning)

Module

3134

Module

3205

Moon Age

Moon Phase

Tidal Movements

Tides are the periodic rise and fall of the water of oceans, seas, bays, and

other bodies of water caused mainly by the gravitational interactions between

the Earth, Moon and Sun. Tides rise and fall about every six hours. The Tide

Graph of this watch indicates tidal movement based on the Moon’s transit over

a meridian and the lunitidal interval. The Tide Graph calculates and graphically

represents current tide conditions in your Home City or a port city in the

vicinity of the Home City based on longitudes, lunar day length, and lunitidal

interval preset in watch memory, and on high tide times specified by you.

Tide Graph

The Tide Graph graphically represents the current tide condition using one of

three patterns that represent spring tide, intermediate tide, and neap tide, as

shown below.

Large difference between

high tide and low tide. Occurs

a few days before and after a

New Moon and Full Moon.

Medium difference between

high tide and low tide.

Small difference between

high tide and low tide. Occurs

a few days before and after

the first quarter and last

quarter of a half moon.

Tide Name Graph Description

Spring Tide

Intermediate Tide

Neap Tide

•

The Tide Graph flashes as shown below to indicate the tide range.

•

The segments on either end of the Tide Graph flash during high tide.

Lunitidal Interval

Theoretically, high tide is at the Moon’s transit over the meridian and low tide

is about six hours later. Actual high tide occurs somewhat later, due to factors

such as viscosity, friction, and underwater topography. Both the time

differential between the Moon’s transit over the meridian until high tide and

the time differential between the Moon’s transit over the meridian until low tide

are known as the “lunitidal interval”.

High tideHigh tide Low tide

Auto Return Features

•The watch returns to the Timekeeping Mode automatically if you do not

perform any button operation for two or three minutes in the Tide/Moon

Data, Alarm, Data Recall, Receive, Digital Compass, or Barometer/

Thermometer Mode.

•

If you do not perform any button operation while in the Altimeter Mode, the

watch returns to the Timekeeping Mode automatically after nine or 10 hours.

•If you leave a screen with flashing digits on the display for two or three

minutes without performing any operation, the watch exits the setting

screen automatically.

Initial Screens

When you enter the World Time or Alarm Mode, the data you were viewing

when you last exited the mode appears first.

Scrolling

The A and C buttons are used on the setting screen to scroll through data

on the display. In most cases, holding down these buttons during a scroll

operation scrolls through the data at high speed.

Sensor Malfunction Indicator

Subjecting the watch to strong impact can cause sensor malfunction or

improper contact of internal circuitry. When this happens, ERR (error) will

appear on the display and sensor operations will be disabled.

•If ERR appears while a measurement operation is being performed in a

sensor mode, restart the measurement. If ERR appears on the display

again, it can mean there is something wrong with the sensor.

•

Even if battery power is at Level 1 or Level 2, the Digital Compass Mode,

Barometer/Thermometer Mode, or Altimeter Mode sensor may be disabled if

there is not enough voltage available to power it sufficiently. In this case,

ERR

will appear on the display. This does not indicate malfunction, and sensor

operation should resume once battery voltage returns to its normal level.

•If ERR keeps appearing during measurement, it could mean there is a

problem with the applicable sensor.

Whenever you have a sensor malfunction, be sure to take the watch to

your original dealer or nearest authorized CASIO distributor as soon as

possible.

Button Operation Tone

The button operation tone sounds any time you

press one of the watch’s buttons. You can turn the

button operation tone on or off as desired.

•Even if you turn off the button operation tone,

the alarm, Hourly Time Signal, and Countdown

Timer Mode alarm all operate normally.

To turn the button operation tone on and off

In any mode (except when a setting screen is on

the display), hold down D to toggle the button

operation tone on ( not displayed) and off (

displayed).

•Since the D button also is the mode change button, holding it down to turn

the button operation on or off also causes the watch’s current mode to

change.

•The indicator is displayed in all modes when the button operation tone is

turned off.

Mute indicator

Elapsed Time in

Dark

60 to 70 minutes

(Display Sleep)

6 or 7 days

(Function Sleep)

Display

Blank, with

PS flashing

Blank, with

PS not flashing

Operation

Display is off, but all functions are

enabled.

All functions are disabled, but

timekeeping is maintained.

Power Saving

When turned on, Power Saving enters a sleep

state automatically whenever the watch is left for

a certain period in an area where it is dark. The

table below shows how watch functions are

affected by Power Saving.

•There actually are two sleep state levels:

“display sleep” and “function sleep”.

•Wearing the watch inside the sleeve of clothing can cause it to enter the

sleep state.

•The watch will not enter the sleep state while the digital time is between

6:00 AM and 9:59 PM. If the watch is already in the sleep state when the

digital time reaches 6:00 AM, however, it will remain in the sleep state.

•The watch will not enter the sleep state while it is in the Digital Compass,

Barometer/Thermometer, Altimeter, Receive, Countdown Timer, or

Stopwatch Mode. When the watch is left in any mode besides the

Countdown Timer and Stopwatch Mode, it will return to the Timekeeping

Mode automatically after a specific amount of time. Then if left in the dark

for the elapsed time indicated in the table above, the watch will enter the

sleep state.

Casio 3134 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio 3134

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info