Operation Guide 3134 3205
14
To recover from the sleep state
P
•Mov
display to turn on.
•Press any b
•Angle the watch tow
To turn Power Saving on and off
1. In the E until
the city code star
the setting screen.
2. Press D nine times until the P
on/off screen appears.
3. Press A to toggle PON ) and
off (OFF ).
4. Press E to e
•The PPS ) is on the
displa
turned on.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
P
indicator
Radio-controlled Atomic
•Strong electrostatic charge can result in the wrong time being set.
•The time calibration signal bounces off the ionosphere.
such factors as changes in the reflectivity of the ionosphere
mov
atmospheric changes or the time of day ma
the signal and make reception temporarily impossible
•Even if the time calibr
can cause the time setting to be off by up to one second.
•The current time setting in accordance with the time calibration signal tak
priority over any time settings y
•
The watch is designed to update the date and da
for the period J
the time calibr
•This watch can receive signals that diff
non-leap years
•Though this watch is designed to receiv
second) and date data (year
limit reception to time data only
•If you are in an area where proper time calibr
impossible, the w
“Specifications ”.
•If you hav
time setting is wrong after signal reception, check your current city code
DST (summer time), and auto receive settings
•The Home City setting reTYO (T
whenev
rechargeable battery replaced.
the setting you want.
T
The time calibration signal received b
selected Home City code.
•When a U
signal transmitted from the United States (F
•When a Japanese time z
calibration signal transmitted from J
•
When a European time zone is selected, the w
signals transmitted from Ger
•When your Home City is LON , PA , BER , or AT (which can receive both
the Anthorn and Mainflingen signals), the watch first tries to pick up the
signal it last successfully received.
the first receive after y
signal first (Anthorn for LON , Mainflingen for PA , BER, and AT).
Timekeeping
•Resetting the seconds to 00 while the current count is in the range of 30 to
59 causes the minutes to be increased b
seconds are reset to 00 without changing the minutes.
•With the 12-hour format, the P (PM) indicator appears on the displa
times in the range of noon to 11:59 p
in the range of midnight to 11:59 a.m.
•With the 24-hour format, times are display
without any indicator
•The 12-hour/24-hour timekeeping f
Mode is applied in all modes.
•The watch ’s built-in full automatic calendar makes allo
month lengths and leap years
reason to change it except when battery power drops to Le
•The times f
Time Mode are calculated in accordance with each city’s UTC offset.
•The UTC offset is a value that indicates the time diff
reference point in Greenwich, England and the time z
located.
Illumination Precautions
•The electro-luminescent panel that provides illumination loses pow
very long use.
•Illumination may be hard to see when vie
•Illumination turns off automatically whenever an alarm sounds.
•The watch may emit an audib
This is due to vibration of the EL panel used f
indicate malfunction.
•F
Auto light s
•The auto light switch is turned off automatically whene
at Lev
•Wearing the watch on the inside of y
vibration of your arm can cause frequent activation of the auto light s
and illumination of the display
the auto light switch whene
frequent illumination of the display
•Note that wearing the watch under your slee
turned on can cause frequent illumination of the display and can run down
the battery
•Illumination may not turn on if the f
watch is more than 15 degrees abo
parallel.
is parallel to the ground.
•Illumination turns off in about one second, even
if you k
face.
•Static electricity or magnetic force can interf
auto light switch.
to the starting position (parallel with the ground) and then tilt it back towards
your f
hangs at your side, and then bring it back up again.
More than 15 degrees
too high
•Under certain conditions, illumination does not tur
second after you turn the face of the watch to
necessarily indicate malfunction.
•Y
shaken bac
the auto light switch, and does not indicate a prob
Barometer and
•The pressure sensor built into this watch measures changes in air
pressure, which you can then apply to y
not intended for use as a precision instrument in official weather prediction
or repor
•Sudden temperature changes can affect pressure sensor readings
•T
you are wearing the watch), direct sunlight, and moisture
more accurate temperature measurement, remov
wrist, place it in a well ventilated location out of direct sunlight, and wipe all
moisture from the case.
case of the watch to reach the actual surrounding temperature
Pressure Sensor and
The pressure sensor and temperature sensor built into the w
calibrated at the f
notice serious errors in the pressure readings and temperature readings
produced by the watch, y
Important!
•Incorrectly calibrating the barometric pressure sensor can result in incorrect
readings.
readings produced by the watch with those of another reliab
barometer
•Incorrectly calibrating the temperature sensor can result in incorrect
readings.
Compare the readings produced by the w
reliable and accurate thermometer
If adjustment is required, remov
or 30 minutes to give the temper
To calibrate the pressure sensor and the temperature sensor
1. Press B to enter the Barometer/
Thermometer Mode.
2. In the Barometer/Ther
down E f
OFF or the reference temperature v
to flash.
•If you want to calibr
pressure sensorD to mov
flashing to the middle display area.
the pressure sensor calibration screen.
•At this time, OFF or the barometric pressure
v
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
•The letters “UTC ” is the abbre“Universal Time ”,
which is the world-wide scientific standard of timekeeping.
carefully maintained atomic (cesium) clocks that k
within microseconds.
to keep UTC in sync with the Earth’s rotation.
