Bedienungsanleitung Casio 5381 - BGA-180 (Seite 3 von 7) (Englisch)

624955

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

Operation Guide 5381

E-29

1. Enter the Thermometer Mode (page E-12).

2. Hold down A for at least two seconds until the temperature

value disappears from the display.

• When you release A the temperature value will start to ﬂ ash.

• The hour and minute hands automatically move out of the way at

this time (page E-15).

3. Use D (+) and B (–) to calibrate the temperature value.

Calibration unit: 0.1°C (or 0.2°F)

Calibration range: –10.0 to 60.0°C (or 14.0 to 140.0°F)

Important!

• To cancel a temperature reading correction setting, hold down D and B at the

same time. The watch will beep.

4. Press A to return to the Thermometer Mode.

E-28

Correcting the Temperature Reading

The temperature sensor of this watch is adjusted at the factory and so further

adjustment is not required by you. However, if you notice that the readings

produced by the watch are different from readings produced by another instrument,

you can use the procedure in this section to make corrections. You also can use

this procedure to clear a correction.

Important!

• The watch will not be able to produce correct temperature readings if you make a

mistake during the correction procedure. Check to make sure that the value you

use for correction produces correct temperature readings.

• Before performing the following procedure, remove the watch from your wrist and

leave it for about 20 or 30 minutes to allow the case temperature to become the

same as the air temperature.

E-27

3. Press C.

• This will cause the current measurement

unit to ﬂ ash.

4. Use D to select the measurement unit you

want.

5. Press A to return to the Thermometer Mode.

Important!

• When TYO (TOKYO) is selected as the Home City, the temperature unit is set

automatically to Celsius (°C). These settings cannot be changed.

E-26

Measurement unit: 0.1°C (or 0.2°F)

Measurement range*: –10.0 to 60.0°C (or 14.0 to 140.0°F)

* - -.- is displayed in place of the temperature when reading is outside the allowable

range.

2. Press C to return to the Timekeeping Mode.

To switch a temperature reading unit between Celsius (°C) and Fahrenheit (°F)

1. Enter the Thermometer Mode (page E-12).

2. Hold down A for at least two seconds until the temperature value disappears

from the display.

• When you release A the temperature value will start to ﬂ ash.

• The hour and minute hands automatically move out of the way at this time (page

E-15).

E-25

Thermometer

This watch uses a temperature sensor to take temperature readings.

• You can select either Celsius (°C) or Fahrenheit (°F) as the temperature

measurement unit (page E-26).

To take a temperature reading

1. In the Timekeeping Mode, press D. This will enter the

Thermometer Mode, which is indicated by TEMP on

the display.

• If TEMP does not appear when you press D, press

it again (page E-12).

• The temperature reading will appear about one

second after TEMP.

• The reading is updated at ﬁ ve-second intervals for two

to three minutes. After that, the watch automatically

returns to the Timekeeping Mode.

Temperature

E-24

Note

• Resetting the seconds to 00 while the current count is in the range of 30 to 59

causes the minutes to be increased by 1.

• The watch’s built-in full automatic calendar makes allowances for different month

lengths and leap years. Once you set the date, there should be no reason to

change it except after you have the watch’s battery replaced.

• The day of the week changes automatically when the date changes.

E-23

3. When the timekeeping setting you want to change is ﬂ ashing, use D and/or B

to change it as described below.

Screen To do this: Do this:

Toggle between 12-hour (12H) and 24-hour

(24H) timekeeping

Press D.

Reset the seconds to 00

Press D.

Change the hour or minute

Use D (+) and B (–).

Change the year

Use D (+) and B (–).

Change the month or day

Use D (+) and B (–).

4. Press A to exit the setting mode.

E-22

2. Press C to move the ﬂ ashing in the sequence shown below to select the other

settings.

City Code

(page E-18)

DST

(page E-20)

12/24-Hour Format

Seconds

Hour

Illumination Duration

(page E-55)

Minutes

Button Operation Tone On/Off

(page E-59)

Day

Month

Year

E-21

Adjusting the Digital Time and Date Settings

Use the procedure below to adjust the digital time and date settings.

To conﬁ gure the digital time and date settings

1. In the Timekeeping Mode, hold down A until ADJ

appears.

• This indicates the city code setting mode.

• The hour and minute hands automatically move out of

the way at this time (page E-15).

E-20

To change the Daylight Saving Time (summer time) setting

1. In the Timekeeping Mode, hold down A until ADJ

appears.

• This indicates the city code setting mode.

• The hour and minute hands automatically move out of

the way at this time (page E-15).

2. Press C to display the DST setting mode.

3. Press D to toggle between Daylight Saving Time (ON)

and Standard Time (OFF).

• Note that you cannot switch between daylight saving

time and standard time while UTC is selected as your

Home City.

4. After the setting is the way you want, press A to

return to the Timekeeping Mode.

• The DST indicator appears to indicate that Daylight

Saving Time is turned on.

DST indicator

Casio 5381 - BGA-180 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio 5381 - BGA-180

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info