Bedienungsanleitung Casio 5381 - BGA-180 (Seite 6 von 7) (Englisch)

624955

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

Operation Guide 5381

E-59

Button Operation Tone

You can turn the button operation tone on or off as

desired.

• Even if you turn off the button operation tone, alarms,

the Hourly Time Signal, and other beepers all operate

normally.

To turn the button operation tone on and off

1. In the Timekeeping Mode, hold down A until ADJ

appears.

• This indicates the city code setting mode.

• The hour and minute hands automatically move out of

the way at this time (page E-15).

2. Press C nine times to display the button operation tone On/Off screen (page E-22).

The screen will show either KEY

or MUTE.

E-58

3. Press C.

• This enters the hour and minute hand adjustment

mode.

• Press C again* to enter the tide hand adjustment

mode.

* Nothing will happen if you press C while the hands

are moving.

4. If the hour and minute hands are not at 12 o’clock,

use D and B to adjust them until they are.

5. Press A to return to the Timekeeping Mode.

Check to make sure that the time indicated by the hands matches the time on the

digital display. If the times don’t match, perform the correction procedure above

again.

Hour hand and minute hand

E-57

Adjusting Hand Positions

The watch hands can go out of alignment with the time on the digital display if it

is exposed to strong magnetism or impact. If this happens, you should adjust the

hand positions.

Important!

• You do not need to perform the operation below as long as the analog hands

indicate the same time as the digital display.

1. Hold down A for about ﬁ ve seconds until H.SET

appears.

• This indicates the tide hand adjustment mode.

• Though ADJ will appear as you hold down A, do not

release the button yet.

2. If the tide hand is not at 12 o’clock, use D and B to

adjust it until it is.

Tide hand

E-56

2. Press C 10 times to display the illumination duration

setting screen (page E-22).

The screen will show either LT1 or LT3.

3. Press D to toggle the illumination duration setting

between LT1 (1.5 seconds) and LT3 (3 seconds).

4. After all the settings are the way you want, press A to

exit the setting screen.

E-55

Illumination

The face of the watch is illuminated for easy reading in the dark.

To turn on illumination

In any mode (except a setting mode), press B to illuminate the display.

Illumination Precautions

• Illumination may be hard to see when viewed under direct sunlight.

• Illumination turns off automatically whenever an alarm sounds.

• Frequent use of illumination runs down the battery.

Changing the Illumination Duration

1. In the Timekeeping Mode, hold down A until ADJ appears.

• This indicates the city code setting mode.

• The hour and minute hands automatically move out of the way at this time (page

E-15).

E-54

To turn an alarm and the Hourly Time Signal on and off

1. In the Alarm Mode, use D to select an alarm or the Hourly Time Signal.

• Each press of D cycles between the alarm time screen and the hourly time

signal SIG setting screen.

2. Press A to toggle the displayed setting (alarm or hourly time signal) between

on and off.

To stop the alarm

Press any button.

E-53

2. Hold down A for about two seconds until the alarm time starts to ﬂ ash. This is

the setting mode.

• The hour and minute hands automatically move out of the way at this time (page

E-15).

3. Press C to move the ﬂ ashing between the hour and minute settings.

4. While a setting is ﬂ ashing, use D (+) and B (–) to change it.

5. Press A to exit the setting mode.

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

E-52

Using the Alarm

The watch beeps for about 10 seconds when the alarm

time is reached. The hourly time signal causes the watch

to beep every hour on the hour.

To set an alarm time

1. Use C to select the Alarm Mode as shown on page E-13.

• This will cause the display to change as shown below.

• If SIG appears on the display, press D.

1 second

Mode name

Alternates

Alarm time ON/OFF

E-51

To perform a countdown timer operation

D D D A

Start Stop (Resume) (Stop) Reset

• Before starting a countdown timer operation, check to make sure that a

countdown operation is not in progress (indicated by the seconds counting down).

If it is, press D to stop it and then A to reset to the countdown start time.

To stop the alarm

Press any button.

E-50

To conﬁ gure the countdown timer

1. While the countdown start time is on the display in

the Countdown Timer Mode, hold down A until the

current countdown start time starts to ﬂ ash, which

indicates the setting mode.

• The hour and minute hands automatically move out of

the way at this time (page E-15).

• If the countdown start time is not displayed, use the

procedure under “To perform a countdown timer

operation” (page E-51) to display it.

2. Use D (+) and B (–) to change the setting.

• You can set a start time in the range of 1 to 60 minutes in 1-minute increments.

3. Press A to exit the setting mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio 5381 - BGA-180 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio 5381 - BGA-180

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info