586703

Casio 5425 Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/6
Nächste Seite
Operation Guide 5146 5425
E-10
3. Press
&
to change the fl ashing screen content in the sequence shown below to
select the other settings.
Seconds
12/24-Hour
Format
Hour
Minutes
DST
Month
Yea r
City Code
Day
Illumination
Duration
4. When the setting you want to change is fl ashing, use
'
or
%
to change it as
described below.
Screen: To do this: Do this:
Change the city code Use
'
(east) and
%
(west).
Toggle the DST setting between
Daylight Saving Time (
on
) and
Standard Time (
OFF
).
Press
'
.
Toggle between 12-hour (
12H
) and
24-hour (
24H
) timekeeping
Press
'
.
E-11
Screen: To do this: Do this:
Reset the seconds to
00
Press
'
.
Change the hour and minutes
Use
'
(+) and
%
(–).
Change the year, month, or day
Toggle the display illumination
duration between 1.5 seconds (
LT1
)
and three seconds (
LT3
)
Press
'
.
5. Press
$
to exit the setting mode.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
E-12
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down
$
for about three
seconds until the currently selected city code fl ashes in
the upper digital display. This is the setting mode.
2. Press
&
. This will display the DST setting screen.
3. Use
'
to toggle the DST setting on (
on
) and off (
OFF
).
• The default DST setting is off (OFF).
4. When the setting you want is selected, press
$
to exit
the setting mode.
• The DST indicator appears to indicate that Daylight
Saving Time is turned on.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
DST indicator
E-13
12-hour and 24-hour timekeeping
• With the 12-hour format, the PM indicator (
P
) appears for times in the range of noon
to 11:59 p.m. and no indicator appears for times in the range of midnight to 11:59
a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
the PM indicator (
P
).
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
E-14
Stopwatch
You can use the stopwatch to measure elapsed time, lap
times and split times. If you specify a distance value, the
stopwatch also will calculate and display speeds.
• The digital display range of the stopwatch is 99 hours,
59 minutes, 59.999 seconds. The stopwatch continues
to run until you stop it. If it reaches the above limit, it will
restart the time measurement from zero.
• The stopwatch operation continues even if you exit the
Stopwatch Mode. If you exit the Stopwatch Mode while
a stopwatch operation is in progress, the segments
along the top of the upper digital display (upper display
segments) will indicate the seconds of the current time.
Each segment represents one second. This is to let you
know that a stopwatch operation is in progress.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing
&
(page
E-7).
Speed hand
Upper display
segments
E-15
Important!
• Check to make sure that the speed hand is not moving before you perform any
Stopwatch Mode button operation.
Specifying a Distance Value
You can use the procedure below to specify a distance value, if you want. If you
specify a distance value, the watch will calculate and indicate speed for certain
stopwatch operations.
• The distance value represents kilometers, miles, or any other distance unit you
want. Specifying a distance value of 10.0, for example, can mean 10.0 kilometers
or 10.0 miles.
• No speed calculation is performed when 0.0 is specifi ed as the current distance
value.
• For lap time readings, you can specify either the lap distance (when all the laps are
the same distance) or the total race distance.
• For split time readings, you can specify the total race distance only. Though the
watch will indicate a speed each time you take a split reading, they will be based
on the total race distance, and so they will not indicate actual intermediate split
speeds.
E-16
To specify a distance value
1. In the Stopwatch Mode, make sure the stopwatch is
stopped and reset to all zeros.
• If you need to reset the stopwatch to all zeros, press $.
2.
Hold down
$
for about three seconds until the current
distance value setting fl ashes in the lower digital display.
• This is the distance value setting mode.
3. Press
&
to move the fl ashing between the values on
the left side and right side of the distance value decimal
point.
4. While a distance value is fl ashing, use
'
(+) and
%
(–)
to change it.
• You can specify a distance value in the range of 0.1
to 99.9.
5. After specifying the distance value you want, press
$
to exit the setting mode.
l
l
l
l
l
l
l
l
l
l
l
E-17
How speed is indicated
• While an elapsed time measurement operation is being
performed in the Stopwatch Mode, the watch will
indicate a speed value, which is calculated based on
the distance you specifi ed and the elapsed time.
The speed value is indicated as described below.
Speed hand: Up to 100
Upper display segments: 100 unit
A
1000
indicator points to 1000 (located to the right of
the upper display segments) when the speed value
exceeds 1000.
• The speed hand indicates speed values less than 100.
Only even-numbered values are indicated.
•
Speed can be indicated from 0 to 1998.
OVER
is indicated
by the speed hand when the speed exceeds 1998.
Example:
When the speed value is 1,740.
Speed hand: Indicates
40
.
Upper display segments: Indicate
700
.
1000
indicator: Displayed
Speed hand
(Up to 100)
Segments
(100 unit)
OVER
1000 indicator
E-18
Time Measurement
You need to specify either lap time (page E-20) or split time (page E-22) measurement
before you start a stopwatch operation.
•
If you want to measure total elapsed time, select split time measurement.
To specify lap time or split time readings
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.
• Make sure that LAP (lap times) or SPL (split times) is shown in the lower digital
display.
• If you need to reset the stopwatch to all zeros, press $.
2. You can toggle between LAP (lap times) and SPL (split times) by pressing
$
.
$
E-19
Elapsed Time Measurement
Use the following procedure to measure elapsed time, without taking lap time or split
time readings.
To perform elapsed time measurement
Select split time (SPL) measurement and then perform the following button operations.
'
Start
➝ '
Stop
➝ $
Reset
•
If you have a distance value (page E-15) specifi ed for the current elapsed time
measurement, the upper display segments and speed hand will indicate the speed
when you press
'
to stop the elapsed time operation.
•
After pressing
'
to stop an elapsed time operation, you could press
'
again to
restart from the point where you left off.
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Casio 5425 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Casio 5425

Casio 5425 Bedienungsanleitung - Deutsch - 6 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info