Bedienungsanleitung Casio PL-40R (Seite 27 von 50) (Englisch)

466869

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

E-59

Using the Sequencer

6. If you want to change mixer parameter settings,

hold down the FUNCTION button and press

PART/(MIXER) button and then configure the

settings you want.

 After setting the parameters you want, press the

EXIT/NO button to return to the recording

screen.

7. Press the RECORD button. This puts the

sequencer into record standby.

8. Play something on the keyboard to start actual

recording.

 If you want to start recording without playing

anything on the keyboard, press the START/

STOP button. A blank space (a series of rests) is

recorded until you play something.

 During recording, the metronome sounds (but is

not recorded) according to current metronome

parameter settings.

9. Play what you want on the keyboard.

 Pedal and other operations are also recorded.

 See “Track 1 to 16 Data” on page E-54 for more

information about the type of data that is

recorded.

10. After you are finished playing what you want,

press the START/STOP button to stop

recording and change to the sequencer’s

playback screen.

 Pressing the START/STOP button at this time

plays back what you just recorded. See “Playing

Back from Sequencer Memory” on page E-60 for

more information about playback.

 Using the Realtime Record Mode to record to a track that

already contains data replaces the existing data with the

new recording.

 If you make a mistake while recording, you can start over

again from step 1 of the above procedure, or use punch in

recording (page E-59) to make modifications.

Use punch in recording to make changes in parts you have

already recorded in a track.

With punch in recording, you listen to the playback of

previous recording, and start playing on the keyboard from

the point where you want to make your modifications.

Everything up to the point where you start playing is

retained, but everything after that point is replaced with your

new input.

Note that you should skip the first two steps of the following

procedure when you go into punch in recording to modify

something you have just recorded.

1. Press the SEQUENCER button.

 This causes the button’s indicator lamp to light,

indicating that sequencer is turned on.

2. Select the song area that contains the song

whose data you want to modify.

 Use [+]/[–] buttons or the selector dial to select a

song area number in the range of 1 to 10.

3. If you want to use the metronome during

recording, make the required metronome

settings.

4. Select the track whose contents you want to

modify.

 Use the [ ] button to select “TrackSelect”.

 Use the [+] and [–] buttons or the selector dial to

select a track.

 After you select a setting, press the SEQUENCER

button or the EXIT/NO button to return to the

play standby screen.

5. Press the ENTER/YES button.

 This enters the punch-in mode and causes the

RECORD button’s indicator lamp to flash.

Modifying Recorded Data with

Punch In Recording

Using Punch In Recording

426-E-061A

PL40NE01-1.book 59 ページ２００２年７月２３日　火曜日　午後６時５２分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Casio PL-40R Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio PL-40R

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info