Bedienungsanleitung Charlton Jenrick Fireline Woodtec 5 (Seite 9 von 28) (Englisch)

707656

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

8 Woodtec Freestanding Issue 01.1 05/17

Where the chimney is believed to have previously served an open fire installation, it is possible

that the higher flue gas temperature from the stove may loosen deposits that were previously

firmly adhered, with the consequent risk of flue blockage. It is therefore recommended that the

chimney be swept a second time within a month of regular use after installation.

If you have any doubts about the suitability of your chimney, consult your local dealer/stockist

or chimney specialist. If there is no existing chimney then either a solid fuel compatible

prefabricated block chimney or a twin-walled insulated stainless steel flue to BS 4543 can be

used. These chimneys must be fitted in accordance with the manufacturer’s instructions and

Building Regulations.

5.2. Ventilation

Document J of the Building Regulations states that purpose provided ventilation is not required

in England and Wales unless the appliance nominal rated output is greater than 5kW. Over 5kW

5.5 cm

of ventilation (550mm

) is required for every kW output above 5. For example 6.5 kW

requires 8.25 cm

and 8 kW needs 16.5cm

. In any case, if difficulty in starting the fire or any

excessive fuming is experienced, ventilation must be put in place as required to eliminate these

flue problems. If a flue draught stabiliser is fitted then extra ventilation is required. See

Document J of the Building Regulations for detailed guidance especially in new build properties.

A specifically designed direct outside air connection may be used with these stoves to provide

appropriate levels of ventilation (significantly in excess of the above requirements) directly to

the stove and chimney as follows. NOTE: in order to register the installation with HETAS as of

early 2016 certain extra evaluation and checking is required if using an outside air connection. If

the direct air kit is used and no ADJ vent is installed then a direct registration with Building

Control may also be possible.

5.3. Direct Outside Air Connection

These stoves are supplied with the facility of using a dedicated 100mm diameter direct

connection duct through a suitable route to the outside air. It can be connected to the rear of

the stove and should be fitted at the time of stove installation. Only the approved kit for these

stoves should be used. This is designed to supply all the necessary air for safe combustion and

operation of the stove – providing there is no depressurisation of the property by mechanical

or other types of ventilation, the flue, chimney and ventilation duct are working correctly, and

properly maintained clear of obstructions or leaks etc. The kit supplies all the primary,

secondary and tertiary air to the stove and also provides room ventilation in excess of the

Document J Building Regulations during re-fuelling via the air connection unit under the stove

and so subject to no depressurisation (as above) may be used where mechanical ventilation and

heat recovery (MVHR) units are used. Some additional instructions for installation are provided

with the dedicated kit supplied. NOTE: in order to register the installation with HETAS as of 2016

certain extra evaluation and checking is required if using an outside air connection. If the direct

air kit is used and no ADJ vent is installed then a direct registration with Building Control may

also be possible.

5.4. Flue Draught

Typically a flue draught at the flue collar of minimum 2.2mm to a maximum 3.5mm water gauge

(22 to 35 Pascals) is required for satisfactory appliance performance. This relates to 12-25

Pascals at the tapping on EN13240/13229 test rigs. The flue draught should be checked under

fire at high output and, if it exceeds the recommended maximum, a draught stabiliser must be

fitted so that the rate of burning can be controlled to prevent over-firing.

5.5. Connection to the Chimney

This appliance is not suitable for use in a shared flue.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Charlton Jenrick Fireline Woodtec 5 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info