Bedienungsanleitung Charlton Jenrick Fireline Woodtec 5 (Seite 10 von 28) (Englisch)

707656

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

9 Woodtec Freestanding Issue 01.1 05/17

Whilst 150mm diameter flue or liner is recommended wherever possible, a suitable 5” flexible

flue liner is permitted be used on these stoves providing that they only burn smokeless fuel or

seasoned wood logs with the air limiter fitted in in full accordance with the wood burning

instructions.

An existing fireplace opening can be bricked up or sealed with a register plate. A short length of

suitable quality rigid flue pipe of a minimum 125mm internal diameter may then be used to

connect the stove to the chimney. A maximum of 150mm horizontal flue pipe can be used. This

flue pipe should conform to Building Regulations. If the connecting pipe enters the vertical flue

way at any other angle except vertically, ensure that the pipe end is no closer (along the

direction of the pipe) than 76mm to the side or rear chimney walls. Ideally, the old fireplace

should be filled in so that there is a smooth streamlined entry into the flue way. It is essential

that all connections between the stove and chimney-flue are sealed and made airtight with

sealing rope, clamping rings and/or fire cement or heat resisting cement where required.

Both the chimney and flue pipe must be accessible for cleaning and if ANY parts of the chimney

cannot be reached through the stove (with baffle removed), a soot door must be fitted in a

suitable position to enable this to be done.

5.6. Material Clearance Dimensions

5.6.1. Safety Distances from Combustible Surfaces:

* To use the minimum clearances from a combustible back wall, the optional heatshield

(supplied with the stove) MUST be fitted and twin wall flue MUST be fitted from the top of

the stove. You must also continue to comply with Building Regulations combustible material

distances from flue pipes unless appropriate heat shielding is used or other information is

available from the flue pipe manufacturer.

In addition it is strongly recommended that any furniture or other combustible materials are

kept at least 900mm clear from the front of the stove.

NOTE: Combustible surfaces can be protected from radiant heat from the stove by adding non-

combustible heat shielding between the stove and the materials with an air gap behind it. By

doing so, safe distances may be substantially reduced in practice.

Model

Side (Full

wall)

Twin Wall

Flue

Side (Full

wall)

Single Wall

Flue

*Rear

Single Wall

Flue

(no shield)

*Rear

Single Wall

Flue

(with shield)

*Rear

Twin Wall

Flue

(no shield)

*Rear

Twin Wall

Flue

(with shield)

Woodtec

5kW

400mm

(From Top

Plate)

450mm

(From Top

Plate)

300mm

(From Top

Plate)

100mm

(From Heat

Shield)

150mm

(from top plate)

75mm (From

Heatshield)

Woodtec

5kW Wide

550mm

(From Top

Plate)

550mm

(From Top

Plate)

300mm

(From Top

Plate)

125mm

(From Heat

Shield)

175mm

(from top plate)

75mm (From

Heatshield)

Woodtec

5kW Xtra

Wide

500mm

(From Top

Plate)

500mm

(From Top

Plate)

250mm

(From Top

Plate)

150mm

(From Heat

Shield)

200mm

(from top plate)

100mm

(From

Heatshield)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Charlton Jenrick Fireline Woodtec 5 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info