Bedienungsanleitung Charnwood SLX 45 MKII - Multi fuel (Seite 6 von 20) (Englisch)

815485

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

The ashpan should be emptied regularly before it becomes too full.

The most convenient time to remove the ash is just before riddling

the fire since the ash will then be at it’s coolest. Use the

ashpan/riddling tool provided to remove the ashpan, the fold up

carrying handle should be held with a heat proof glove.

Never allow the ash to accumulate in the ashpan so that it comes in

contact with the underside of the grate as this will seriously damage

the grate bars. Ensure that the air inlet damper is not prevented

from closing by spilled fuel or ash.

Care should be taken to ensure that ash is cool before emptying it

into plastic liners or bins.

To make ash removal easier there is a special Charnwood ash

carrier available. This may be purchased from your supplier or, in

case of difficulty, from ourselves.

RIDDLING

REFUELLING

OVERNIGHT BURNING

The fire should be riddled with the doors shut. Place the tool on the

knob and rotate between the horizontal and the 45° position

several times as shown in Fig. 2.

Caution: when riddling the grate using solid fuel do not go beyond

the 45° position as this can cause the grate to jam.

If jamming does occur then the fire should be allowed to burn for

approximately half an hour before riddling the grate again as

described above. Riddling twice a day is usually sufficient when

burning solid fuel. When burning wood, ash should be allowed to

build up and only riddled when the ash begins to cover the slots in

the rear fireplate.

Too much riddling can result in emptying unburnt fuel into the

ashpan and should therefore be avoided. Clinker should regularly be

removed from the firebed.

After riddling, the grate should be put back into the solid fuel or

wood position as required (the tool should be horizontal for solid

fuel or vertical for wood).

Keep the firebox well filled (the fuel may be sloped up from the front

firebars), but do not allow fuel to spill over the top of the front fire

bars. Take care that fuel does not project over the front fire bars or

damage to the glass may be caused when the doors are closed.

For overnight burning the fire doors must be closed.

When burning solid fuel the ashpans should be emptied and the fire

riddled. If the fire is very low then it may be necessary to add a little

fuel and turn the thermostat control up to maximum for a brief

period until the fire is burning brightly before filling with fuel. When

the new fuel has ignited, the thermostat control should be turned

down to the required setting and the airwash control moved to a

low setting. If the central heating pump is off overnight then the

thermostat may be left at the same setting for both day and night

operation. If the central heating pump is on overnight then set the

thermostat control to give the required level of heating.

Some experimentation will be necessary to find the settings most

suitable for the particular fuel used and the draw on the chimney. To

revive the fire, empty the ashpans, riddle, and open the air controls

to maximum. When the fire is burning well load on more fuel as

necessary and move the air controls to the desired setting.

When burning wood use large logs rather than small ones. Proceed

as above, but do not riddle the fire either when shutting down or

reviving.

THROATPLATE AND

FLUEWAY CLEANING

It is important that the throat plate and all the appliance flueways

are kept clean. When burning smokeless fuels they should be

cleaned at least monthly and more frequently if it is found necessary.

The throat plate and flueways may be cleaned with a low fire still

burning. Use the scraper tool to scrape any sooty deposits off the

front of the plate until they fall into the fire. Also scrape any soot

deposits from the sides and top of the firebox. Ensure that soot

deposits are not allowed to build up on the sides because if the

throat plate becomes tight between the faces this can cause it to fail

prematurely.

More soot will be deposited on the throat plate and in the flueways

if the appliance is run at low levels for long periods. If this is the case

then more frequent cleaning will be necessary.

SPECIAL POINTS WHEN BURNING

COAL

When loading the appliance take care not to smother the fire,

instead fill the firebox in two stages waiting between each stage for

the flames to appear above the fire.

After a period of slumbering always turn the air control up to

charnwood

OPERATING INSTRUCTIONS SLX45

MU LT I-F UEL

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Charnwood SLX 45 MKII - Multi fuel Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info