Bedienungsanleitung Christopeit AL5 - 1124 (Seite 15 von 44) (Deutsch, Englisch, Holländisch, Französisch)

644073

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

English

Step 2:

Attach the front post (38) at main frame (1).

1. Hold the handlebar support (38) with the computer cable (40) against

the main frame holder. Connect the plug for the computer cable (40)

coming out of the bottom of the handlebar support (38) of the computer

with the matching plug for the sensor cable (41) coming out of the main

frame (1).

(Note: The computer cable harness (40) projecting from the support (38)

must not slide into the tube, as it is required for later steps of installation.)

2. Connect the resistance control (52) to the bracket of lower section cable

tension (70) (See ﬁgure [1]-[4]). Before this step of the installation, it is

advisable to adjust the resistance setting to the highest stage, at which

the cable extends furthest from the sheath. Put the lowest part of cable

(52) into the small hook (ﬁgure 1+2). Pull it (ﬁgure 3) until the small hook

get in higher position and then insert the cable (14) onto the bracket

(70) (ﬁgure 4).

3. Place the handlebar support (38) in the locator provided for it in the main

frame (1). Ensure that the cable connections made are not squashed.

When putting the steering tube in place, push the former slowly down

into the locator in the main frame. Screw the handlebar support (38)

onto the base frame (1) with the screws (39), spring washers (42) and

washers 8//25 (3).

4. Mount handlebar cover set (37L+37R) to the handle bar support (38)

and secure with screws (51).

Assembly Instructions

Remove all the separate parts from the packaging, lay them on the ﬂoor

and check roughly that all are there on the base of the assembly steps.

Please note that a number of parts have been connected directly to

the main frame and preassembled. In addition, there are several other

individual parts that have been attached to separate units. This will

make it easier and quicker for you to assemble the equipment.

Step 1:

Attach the stabilizer (5+43) at main frame (1).

1. Attach the front foot (43) with the preassembled transport rollers (44) to

the main frame. Do this with the two screws M8x75 (6), curved washers

8//25 (3), spring washers (42) and cap nuts (2).

Attention: Mount the front foot into right direction, so that the transport

rollers don’t touch the ﬂoor during exercising.

2. Attach the rear foot (5) with height adjustable foot caps (4) to the main

frame (1). Do this with the two screws M8x75 (6), curved washers 8//25

(3), spring washers (42) and cap nuts (2). After assembly has been

completed, you can compensate for minor irregularities in the ﬂoor by

turning the wheel at cap (4). The equipment should be set up that the

equipment does not move of its own accord during a training session.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Christopeit AL5 - 1124 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info