Bedienungsanleitung Ciclo HAC 4 Pro (Seite 6 von 15) (Englisch)

588929

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

HL 2 – heart rate upper limit 2

Set with UL- or LL-button

Standard value = 120 bpm (beats per minute)

or the personal upper limit calculated with

CICLO

Zone®

Setting range min. = 30 bpm; max. 240 bpm

HL 2 – heart rate lower limit 2

Set with UL- or LL-button

Standard value = 100 bpm (beats per minute)

or the personal upper limit calculated with

CICLO

Zone®

Setting range min. = 30 bpm; max. 240 bpm

Cd 1 – Countdown 1

Set with UL- or LL-button

Standard value = 10 minutes

Setting range = 0 - 99.59 minutes

1. Countdown 1 / Countdown 2 is a stop-watch which runs

backwards (see chap. 5.2, “countdown function“). After starting, the

HAC gives a short signal when CD 1 reaches 0. Then CD

2 starts automatically, when it reaches 0 it gives short signals for 20

sec. If only one countdown is necessary, the other must be set to 0.

2. These settings are necessary when using the heart rate time

manager (see chap.6. “special functions”).

Cd 2 – Countdown 2

Set with UL- or LL-button

Standard value = 10minutes

Setting range = 0 - 99.59 minutes

Cc oFF/on – Cadence on/off

Select with UL- or LL-button

Standard value = oFF

Here the cadence measurement can be swit-

ched on or off (measurement is only possible

with the optional cadence kit).

The following two settings only appear, when cadence is switched

‚on‘.

UL – upper limit for cadence

Set with UL- or LL-button

Standard value = 180 rpm (rounds per minute)

Setting range min. = 30 rpm; max. 240 rpm

In order to better control your training, a ca-

dence limit (lower and upper limit) can be set.

When current cadence value is below or above the limits, an optical

alarm occurs (cadence value starts blinking).

LL – lower limit for cadence

Set with UL- or LL-button

Standard value = 120 rpm (rounds per minute)

Setting range min. = 30 rpm; max. 240 rpm

U1 – unit kilometre/mile

Select with UL- or LL-button

The unit of measure for distance and speed

can be set here (kilometres or miles).

U2 – Time-of-day display: 24- or 12-hour

Select with UL- or LL-button

If 12-hour indication is selected, automatically

also the american date format (month/day) and

weight unit lbs is chosen.

U3 – Unit °Celsius/°Fahrenheit

Select with UL- or LL-button

The unit of measure for the temperature can be

set here (°celsius or ° fahrenheit).

U4 – Unit altimeter meter (m) /

feet (ft x 10)

Select with UL- or LL-button

The unit of measure for the altitude can be set

here (meter or feet).

UPL – Upload Version

Start with short simultaneous pressing of UL-

and LL-button

Indicates the firmware-version of the HAC

. If there is a newer firmware available

for your HAC (see www.ciclosport.

de), you can start the firmware upload at this point with short

simultaneous pressing both left buttons (UL- and LL-button), that

is only possible with the optional pc-interface and the program

HACtronic.

When the upload is finished correctly, normal mode appears in the

display.

Pd – Power down-mode

Switch on with short simultaneous pressing of

UL- and LL-button

Starts the power-saving mode (see chap. 5.3).

To end the power-saving mode, press any

button.

4.2 setting mode 2

Press LR-button 4 sec.

A – Setting and / or re-adjusting current

altitude

Set with UL- or LL-button

Setting range = -200m to 9000m or

2952 ft x10

The current altitude can be adjusted, if e.g. due to variations in the

air-pressure, the current altitude shown in the HAC is not

correct.

A change in the current altitude has no effect on other altitude func-

tions (e.g. total meters). Only if the adjusted altitude is higher than the

current max. altitude, the max. altitude will be changed to the new

value.

DST – adjust daily distance

Set with UL- or LL-button

Standard value = 0 km

Setting range min. = 0,00 km /m;

max.= 999,99 km / 621,36 m

(in the display the comma is shown as a colon)

The daily kilometres can be adjusted here, e.g. as a starting point

in case of tours according to a tour guidebook, if the tour was not

entered at „0“ km.

This setting does not affect the function total kilometres. There only

the really ridden kilometres are counted.

JS oFF/on – Ski mode on/off

Select with UL- or LL-button

If the HAC is used while skiing, the

ski speed is only calculated and indicated if this

function is set ‚on‘.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ciclo HAC 4 Pro Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ciclo HAC 4 Pro

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info