Bedienungsanleitung Ciclo HAC 4 Pro (Seite 10 von 15) (Englisch)

588929

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

Countdown

To start the countdown (resp. the

heart rate time manager) press

start/stop-button short.

After starting the HAC

counts back the indicated time to

zero. Then it gives a short signal and starts automatically the count-

down 2. After counting back the countdown 2, the HAC

gives a long signal (stop the signal with short pressing any button).

By pressing start/stop-button 3 sec. the countdown is set back to

the start value (of countdown 1).

The function ‚countdown‘ is also used by the function ‚heart rate

time manager‘, see chap. 6.2.

Comparison

(only in bike mode)

See also chap. 6.4. The current tour can be

compared with a previous tour (same course).

During the comparison, the display shows

constantly if you are faster or slower as on the

compared tour (accuracy = +/- 1 sec.).

To choose the tour being compared, see below. At the end of the

comparison a short signal tones and the recording is automatically

stopped. The last compare time is still indicated and the ‚new‘ tour is

stored for a new comparison.

To start the comparison (and with this start the recording) press the

UL- and LL-button simultaneously 4 sec. (to stop the comparison

premature press again the UL- and LL-button simultaneously 4 sec).

Choose a tour for comparison

(only in bike mode)

Sub-function of function ‚Comparison‘ (see

also 6.4).

Press the LL-button repeatedly short, all stored

tours are (descending) indicated in the display

(date and start time appear changing). The tour you leave indicated

in the display, is chosen. If you do not want to choose a tour, leave

the “----“ indicated in the display.

After choosing the tour, press UL- and LL-button simultaneously

4 sec. to start the comparison (and therewith start the recording).

Note: A tour for comparison can only be chosen, when the recor-

ding is not yet started.

Cadence (optional)

(only in bike mode)

The function ‚Cc‘ must be switched ‚on‘ in

setting mode 1 (chap. 4.1) and the optional

cadence cable must be mounted to measure

and indicate the cadence.

Range: 0 - 240 rpm (= revolutions per minute )

Average cadence

(only in bike mode)

Sub-function of function ‚Cadence‘.

Indicates the average cadence of the current

tour.

Range: 0 - 240 rpm

Maximum cadence

(only in bike mode)

Sub-function of function ‚Cadence‘.

Indicates the maximum cadence of the current

tour.

Range: 0 - 240 rpm

Number of revolutions (only in bike mode)

Sub-function of function ‚Cadence‘.

Indicates the number of revolutions of the

current tour.

Range: 0 – 999999 revolutions (the 6. position

is shown on the decimal point of the upper

display)

Daily ride time

(only in bike mode)

Indicates the time travelled (without stopping-

times, i.e. the time is only calculated when the

wheel turns).

The measurement starts with the first and ends

4 sec. after the last turn of the wheel.

Range: 0 – 999:59 (up to 10 hours the display shows: h:mm:ss, 10

hours and more: hhh:mm)

Sum of the daily ride time

(only in bike mode)

Sub-function of the function ‚Daily ride time‘.

Indicates the sum of the time travelled with bike

1 and bike 2.

Range: 0 – 999:59 (up to 10 hours the display

shows: h:mm:ss, 10 hours and more: hhh:mm)

Total ride time

(only in bike mode)

Sub-function of the function ‚Daily ride time‘.

Indicates the total time travelled.

Range: 0 - 999:59 h

Sum of total ride time

(only in bike mode)

Sub-function of the function ‚Daily ride time‘.

Indicates the sum of the total time travelled with

bike 1 and bike 2.

Range: 0 - 999:59 h

Current altitude

Indicates the current altitude in meters or ft x10

(above sea level). It is indicated in steps of 1

m/10 ft .

As the altitude depends on the air-pressure,

the measurement may vary according to the

weather situation.

Range: -200m to 9000m resp. 2952 ft x10

Daily altitude increasing

Sub-function of function ‚Current altitude‘

Indicates the current increase (meters/ft) in

altitude for the current tour.

Range: 0 - 99999 m resp.

32808 ft x10

Daily altitude decreasing

Sub-function of function ‚Current altitude‘

Indicates the current decrease (meters/ft) in

altitude for the current tour.

Range: 0 - 99999 m resp.

32808 ft x10

Total altitude increasing

Sub-function of function ‚Current altitude‘

Indicates the total increase (meters/ft) in alti-

tude.

Range: 0 - 99999 m resp.

32808 ft x10

Total altitude decreasing

Sub-function of function ‚Current altitude‘

Indicates the total decrease (meters/ft) in

altitude.

Range: 0 - 99999 m resp.

32808 ft x10

Note: Technically restricted the daily and total amount of meters/ft.

are only added if at least 2 meters have been exceeded.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ciclo HAC 4 Pro Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ciclo HAC 4 Pro

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info