Bedienungsanleitung Ciclo HAC 5 (Seite 12 von 38) (Englisch)

588931

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

If the initialization is not successful, the percentage runs up to 100 % and the HAC5 shows “Iniscan

Error retry cancel“ afterwards.

Activate transmitter once again after this and start initialization once again by selecting “retry” (LR-

button,

confirm with

MR-button).

“cancel” (select with

LR-button)

Through “cancel“ (select with LR-button and confirm with MR-button), the Initialization function can be

left (HAC5 shows the selecting menu again).

Press LR-button once to select “CAD“

Confirm with MR-button

Display shows “CAD on/off“, “on“ is marked.

Confirm with MR-button

Display shows “Iniscan CAD yes/no“, “yes“ is marked.

Now activate the cadence transmitter (pick it up and gently knock the spoke magnet against the mark

of the transmitter a few times, this starts the transmitter and it gives a signal.

Caution: The display of the HAC5 remains unchanged during the activation).

Confirm with MR-button (please confirm only after the transmitter is activated).

Display will shortly show a percentage and returns back to selection mode after successful Initialization

(display shows “CAD“ marked). Should the Initialization be unsuccessful see further up.

Press LR-button once to select “HR“

Confirm with MR-button

Display shows “HR on/off“, “on“ is marked.

Confirm with

MR-button.

Display shows “Iniscan HR yes/no“, “yes“ is marked.

If you have already put on the breast strap, it should already be activated. If not, activate it “manually“:

take the strap into your hands and rub it right and left on the ribbed parts with your thumbs, the trans-

mitter turns on through the friction and gives a signal.

Caution: the display of the HAC5 remains unchanged during activation.

Confirm with MR-button.

Display now shortly shows a percentage and returns to the section menu after successful Initialization

(Display shows “HR“ marked). Should the Initialization be unsuccessful see further up.

Press

MR-button for three seconds to leave the settings mode.

Through the settings in the “Bike1“ profile, this profile is already automatically “selected“, meaning the

display now shows the normal function mode of the “Bike1“ profile.

Now you can install the transmitters, the HAC5 is ready for use in terms of Initialization.

You can of course enter all the other data like wheel circumference, weight, measurements etc. first, to

do so follow the structure of the above example and enter the data in the setting mode concerned.

Important: Altogether, two speed transmitters, two cadence transmitters, one RDS II and one heart

rate transmitter can be initialized.

That means if you have already initialized the heart rate transmitter for “Bike1“, you only have to turn

on this function in the other profiles (“on“), you don’t have to initialize again (select “no“ for “Iniscan HR“

and then confirm with the MR-button).

An already initialized speed- or cadence transmitter for “Bike1“ cannot be initialized for “Bike2“. Only if

another transmitter was initialized for “Bike1“ (or an Initialization was made without transmitter, which

then breaks off with “error“) can the original transmitter be initialized for “Bike2“.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ciclo HAC 5 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ciclo HAC 5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info