Bedienungsanleitung Citronic MPSD-2 (Seite 4 von 20) (Englisch)

455896

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

1. SOURCE SELECT BUTTON – This button lets you toggle between USB Port and SD Card slots. This lets

you choose which music source device will play on either side. The LEDs will verify which source is

activated. Glowing green “A” LED signifies USB A port, green “A” LED is blinking signifies CARD A slot；

Glowing red “B” LED signifies USB B port, red “B” LED is blinking signifies CARD B slot. The function can

only be selected under pause mode.

2. MEMORY BUTTON – This button allows you to program up to 4 cue points or 4 loops into the 4 CUE

BANK BUTTONS. The loops or cue point can then be recalled at any time even when the music source

device has been removed and reloaded at a later time.

3. CUE BANK BUTTONS – These buttons are used to store either 4 cue points or 4 loops. Each Bank Button

can store either a loop or a cue point.

4. CUE BUTTON – Pressing the CUE button during playback immediately pauses playback and returns the

track to the last set cue point. The CUE LED will glow when the unit is in cue mode. The LED will also flash

every time a new CUE POINT is set. The CUE button can be held down to momentarily play the music.

When you release the CUE button it instantly returns to the CUE POINT. You can also tap the CUE button

to create a STUTTER EFFECT.

5. PLAY/PAUSE BUTTON – Each press of the PLAY/PAUSE BUTTON causes the operation to change from

play to pause or from pause to play. While in play mode the PLAY/PAUSE LED will glow, and while in pause

mode the PLAY/PAUSE LED will flash.

6. JOG WHEEL – This wheel has 3 functions:

The wheel works as a pitch bend during Playback. Turning the wheel clockwise can increase the pitch

percentage up to 100%, and turning the wheel in the counterclockwise direction can decrease the pitch

percentage down to -100%. The pitch bend will be determined on how long you turn the jog wheel

continuously.

The jog wheel acts as a slow frame search (1/75 sec) control when the music is not playing but either paused

or set to a cue point. To set a new cue point, spin the wheel then press PLAY or IN when you have

determined the proper position. Press CUE to return to the “CUE POINT”.

If the search function is active, you will be able to search at a higher speed through all the tracks.

7. MIXED OUTPUT BUTTON – This button is used to switch the output signal between MIXED OUTPUT and

PLAYER 1. When the MIXED OUTPUT is activated, the output will send a mixed output signal. You can

connect the mixed output of the player directly to an amplifier or a set of powered speaker cabinets. If the

MIXED OUTPUT is not activated, the output will send player 1 output signal.

Press the MIXED OUTPUT button for more than 2 seconds to switch MIXED OUTPUT on/off.

8. POWER SWITCH BUTTON – It is used to switch the power on/ standby. When power cord plug into the

rear socket to be the STANDBY mode, all LED are off but STANDBY LED.

(a) In the STANDBY mode, press power button to POWER ON, ”

Please insert memory device” is

displayed in the LCD.

(b) In the POWER ON mode, press and hold the power button more than 2sec. to standby.

9. CROSSFADER – This fader is used to blend the output signals of player 1 and 2 together. When the fader

is in the full left position (player 1), the output signal of player 1 will be controlled by the master volume

level. The same fundamentals will apply for player 2. Sliding the fader from one position to another will vary

the output signals of player 1 and 2 respectively. When the crossfader is set in the center position, the

output signals of both the player 1 and player 2 will be even.

10. FADER START SWITCH –used to choose between the external and internal fader starts:

 INTERNAL FADER START (Fader start switch UP): the fader start will only react on the crossfader (9)

of the internal mixer.

The external CONTROL START input(s) (32) are not active. With this function you

can use the crossfader (9) to start and stop the player. The FADER START switch (10) activates the

fader start feature. When the fader start feature is activated sliding the crossfader from left to right will

play or cue the player connected.

Example: Be sure the Fader Start feature is activated on. Slide the crossfader to the player 1 position

(full left) and begin playback on player 1. Slide the crossfader to the player 2 position (far right), this will

immediately trigger the play function on player 2 and return player 1 to cue mode.

 Fader start switch DOWN: the fader start will not work with the crossfader (9) of the internal mixer.

The external CONTROL START input(s) (32) can be used to start/stop the players with mixers that are

compatible with your fader start compatible mixer.

CONTROLS AND FUNCTIONS TOP PANEL

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Citronic MPSD-2 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info