Bedienungsanleitung Citronic MPSD-2 (Seite 6 von 20) (Englisch)

455896

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

CONTROLS AND FUNCTIONS TOP PANEL

CONTROLS AND FUNCTIONS REAR PANEL

23. RELOOP BUTTON – If a SEAMLESS LOOP has been made, but the Player is not actively in SEAMLESS

LOOP mode (a loop is not playing), pressing the RELOOP BUTTON will instantly reactivate the

SEAMLESS LOOP mode. To exit loop, press the OUT BUTTON. LOOP and RELOOP will appear in the

LCD DISPLAY when the RELOOP function is available.

24. MASTER VOLUME CONTROL – This knob is used to control the master output level. To avoid speaker

damage that may be caused by excessive volume, be sure this knob is always set to the lowest level

before turning the unit on(only available when MIXER OUTPUT is ON).

25. SD CARD SLOTS – These are the SD slots where you insert your SD cards. One card per slot. Gently

insert your SD Card into the slot. To eject your card, put the Media Operator in pause mode, and then

press the SD Card gently. The SD Card should "Pop" out. The preferred file format is Mp3.

26. USB PORT – This is the USB port where you insert your USB mass storage device for playing MP3 files.

27. MICROPHONE VOLUME CONTROL – This knob controls the output volume of the MICROPHONE (only

available when MIXER OUTPUT is ON).

28. INPUT FADER (Channel Fader) – These faders are used to control the output signal of any source assigned

to its particular player (only available when MIXER OUTPUT is ON).

29. PITCH SLIDER – This slider is used to adjust the playback pitch percentage. The slider is a set adjustment

and will remain set until the pitch slider is move or the pitch function has been turned off. This adjustment

can be made with or without a music source device (USB stick or SD card) in the player. The pitch

adjustment will remain even if a music source device (USB stick or SD card) has been removed and will

reflect on any other music source device inserted into the player. That is to say, if you set a +2% pitch on

one music source device, remove that device and insert another, that music source device too will have a

+2% pitch. The amount of pitch being applied will be displayed in the LCD.

30. LCD DISPLAY – This high quality LCD display indicates all the functions, as they are occurring. This

display is viewable at several comfortable angles.

31. AUDIO OUTPUTS – AUDIO OUTPUT from player 2: Output for the audio signal from player 2. Use the

supplied RCA phono leads to connect these outputs to the CD/line input of an external mixing unit.

32. CONTROL START sockets – This remote control is only compatible with certain mixers. If you are using a

mixer with fader start function, use this connector to plug into your fader start compatible mixer.

Attention: Please note that these sockets must never be connected with any voltage.

33. POWER CONNECTOR – Plug in power adapter here. It is a switching adapter to suitable to each voltage.

34. AUDIO OUTPUT from player 1 or mixer –Output depending on the setting of the MIXER OUTPUT MODE.

35. BALANCED OUTPUTS JACKS – These jacks send a balanced output signal.

36. MICROPHONE – This jack is used to connect a microphone to the device. The volume output level for this

microphone will be controlled by its own respective volume knob.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Citronic MPSD-2 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info