Bedienungsanleitung Clarion FZ502E (Seite 7 von 16) (Englisch)

580546

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

English

FZ502E

Radio Operations

Select tuner as playing source

Press the [CONTROL] knob or [SRC]

button on the remote control once or more

to enter RADIO mode.

Select one radio band

Press and hold the [CONTROL] knob (up

long press) on the panel or [BAND/TOP]

button on the remote control to select one

radio band among FM1, FM2, FM3, MW

and LW.

Manual tuning

During manual tuning, the frequency will be

changed in steps.

Press the [CONTROL] knob (left / right)

on the panel or [

, ] buttons on the

remote control to tune in a higher / lower

station.

Auto tuning

Press and hold the [CONTROL] knob (left

/ right) on the panel or [

, ] buttons on

the remote control to seek a higher / lower

station.

To stop searching, repeat the operation

above or press other buttons having radio

functions.

Note:

When a station is received, searching stops

and the station is played.

Preset scan

Preset scan receives the stations stored

in preset memory in order. This function is

useful when searching for a desired station

in memory.

1. Press the [SCN/PS/AS] button on the

remote control .

2. When a desired station is tuned in, press

the [SCN/PS/AS] button on the remote

control again to continue receiving that

station.

Note:

Be careful not to press and hold the

[SCN/PS/AS] button, otherwise the auto

store function is engaged and the unit starts

storing stations.

Auto store

Only stations with sufcient signal strength

will be detected and stored in the memory.

Press and hold the [SCN/PS/AS] button on

the remote control to start automatic station

search.

To stop auto store, press other buttons

having radio functions.

Notes:

1. After auto store, the previous stored

stations will be overwritten.

2. The unit has 5 bands, such as FM1, FM2,

FM3, MW, LW. FM3 and MW, LW can

store by AS function. Each bands can

store 6 stations, FZ502E can store 30

stations in total.

Manual store

When one expected radio station has been

detected, press and hold number button

on the remote control 1-6 to store it in the

memory.

Recall the stored stations

Press one numeric button among 1 to

6 on the remote control to select the

corresponding stored station.

Press the [CONTROL] knob (up / down) on

the panel to tune in a higher / lower station.

Local seeking

When LOCAL seeking is on, only those radio

stations with strong radio signal could be

received.

To open or close LOCAL function, set to

system setup by long pressing [CONTROL]

knob on the front panel, then press the

[CONTROL] knob(left / right) repeatedly until

LO or DX displays on the screen, rotate the

[CONTROL] knob to select Local or Distant

mode.

Note:

The number of radio stations that can be

received will decrease after the local seeking

mode is on.

Radio Data System Operations

Radio Data System

This unit has a built-in “Radio Data System”

decoder system that supports broadcast

stations transmitting “Radio Data System”

data.

When using the “Radio Data System”

function, always set the radio to FM mode.

AF function

The AF function switches to a different

frequency on the same network in order to

maintain optimum reception.

* The factory default setting is ON.

1. In ADJ m ode(RADIO mode), press

[CONTROL] knob (left / right) to select

options.

2. Press the [CONTROL] knob (left / right) to

select “AF”.

3. Rotate the [CONTROL] knob to select ON

or OFF.

• AF ON:

“AF” indicator appears in the display and

AF function turns on.

• AF OFF:

“AF” indicator disappears in the display

and AF function turns off.

REG (Regional programme)

function

When the REG function is ON, the optimum

regional station can be received. When this

function is OFF, if the regional station area

switches as you drive, a regional station for

that region is received.

* The factory default setting is ON.

Notes:

• This function is disabled when a national

station such as BBC R2 is being received.

• The REG function ON/OFF setting is valid

when the AF function is ON.

1. In ADJ mode, press [CONTROL] knob (left

/ right) to select options.

2. Press the [CONTROL] knob (left / right) to

select “REG”.

3. Rotate the [CONTROL] knob to select ON

or OFF.

Manually tuning a regional station

in the same network

1. This function is valid when the AF function

is ON and the REG function is OFF.

Note:

• This  f unction can be u sedwhen  a

regionalbroadcastofthesamenetworkis

received.

TA (Trafc Announcement)

In the TA standby mode, when a trafc

announcement broadcast starts, the trafc

announcement broadcast is received as top

priority regardless of the function mode so

you can listen to it. Trafc programme (TP)

automatic tuning is also available.

* This function can only be used when

“TP” appears in the display. When “TP”

appears, this means that the “Radio Data

System” broadcast station being received

has trafc announcement programmes.

Setting the TA standby mode

If you press the [TA] button on the remote

control (in ADJ mode, press [CONTROL]

knob (left / right) to select options) “TA” lights

in the display and the unit is set into the TA

standby mode until a trafc announcement

is broadcast. When a trafc announcement

broadcast starts, “TRAF INF” appears in the

display. If you press the [TA] button on the

remote control while a trafc announcement

broadcast is being received, the traffic

announcement broadcast reception is

cancelled and the unit goes into the TA

standby mode.

Cancelling the TA standby mode

As “TA” lights in the display, press the [TA]

button on the remote control. The “TA” in the

display goes off and the TA standby mode is

cancelled.

PTY (Programme Type)

This function enables you to listen to a

broadcast of the selected programme type

even if the unit is on a function mode other

than radio.

* Some countries do not yet have PTY

broadcast.

* In the TA standby mode, a TP station has

priority over a PTY broadcast station.

Selecting PTY

In ADJ mode, press [CONTROL] knob

(left / right) to select options, then rotate

the [CONTROL] knob to select PTY type,

press the [CONTROL] knob, the unit begin

searching.

Clarion FZ502E Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Clarion FZ502E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info