652338
63
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
63Mounting and installation work
5.7.6 Installation work external connections
Connecting the external safety chain
B3
B2
B1
MAINS SUPPLY
L N SC1SC2PEPE
J3
K2
Control compartment
Do not apply extraneous
voltage via K2!
DANGER: 230 V
The potential-free contacts of external moni t or ing de-
vices (e.g. ventilation interlock "B1", airow monitor "B2",
safety high limit humidistat "B3", etc.) are connected in
series (safety chain "K2") to the terminals "SC1" and
"SC2" of the terminal block "X1" on the driver board in
accordance with the wiring diagram.
The connecting cable must be led through a cable gland
into the control compartment.
Caution! A high limit humidistat is highly recomen-
ded to prevent risk of over-humidication and potential
damage to property.
Note: If, for whatever reason, no external monitoring de-
vices are connected, a jumper wire "J3" must be installed
on the contacts "SC1" and "SC2" of the terminal block.
CAUTION! Do not apply any extraneous voltage to
contacts "SC1" and "SC2" via the contacts of the
external monitoring devices.
Humidity control wiring
Connecting a demand or humidity signal
CONTROL
V+ IN GND
JP2 (24V)
JP1 (10V)
+
A1
Y
24V/
10V
Control compartment
The signal cable of an external controller or of a humid-
ity sensor (if the internal P/PI controller is used) are to
be connected according to the wiring diagram to the
terminals "IN" and GND" on the driver board in the
control compartment. The connecting cable must be
led through a cable gland into the control compartment.
Note: if the external controller or the humidity sensor
shall be supplied with 10 V or 24 V from the driver board
(terminal “A+”), the jumper JP1 must be set to 10V or
24V accordingly.
Note: the humidity control must be congured via the
control software accordingly. The admissible humidity
control signal values can be found in the technical data
table in the operation manual.
If a shielded signal cable is used, connect the shielding
to terminal "GND".
Caution! If the shielding of the control signal is already
connected to a po ten tial or a grounded conductor,
do not connect it to terminal "GND"
63

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Condair RS wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Condair RS

Condair RS Bedienungsanleitung - Englisch - 80 seiten

Condair RS Bedienungsanleitung - Holländisch - 80 seiten

Condair RS Installationsanweisung - Holländisch - 76 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info