652338
65
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
65Mounting and installation work
Connecting an external ohmic limiter controller
LIMIT
IN GND
140Ω...10kΩ
A5
CONTROL
V+ IN GND
JP2 (24V)
JP1 (10V)
Control compartment
The signal cable of an ohmic limiter controller
(140Ω...10kΩ) is to be connected according to the wir-
ing diagram to the terminals "V+" (CONTROL terminal)
and "IN" and GND" (LIMIT terminal) on the driver board
in the control compartment.
The connecting cable must be led through a cable gland
into the control compartment.
Note: when connecting an ohmic limiter controller
Jumper "JP2" must be removed and Jumper "JP1" must
be connected on the driver board. The limiter must be
activated and limiter signal type must be set to 0-10V
in the control settings of the control software.
Connecting the optional remote operating and fault indication
Error Service Steam Unit On
F1 (100 mA)
H1
1 2 3
4 5 6
7 8
9 10
Control compartment
The optional remote operating and fault indication board
contains four potential-free relay contacts for the con-
nection of the following operating and fault indications:
"Error" (Terminal 1 and 2):
This relay is activated if an error is present.
"Service" (Terminal 4 and 5):
This relay is activated when the set maintenance
interval has elapsed.
Note: this relay can be congured in the control
software to close either when maintenance is re-
quired or when maintenance is required and when
a warning is indicated.
"Steam" (Terminal 7 and 8):
This relay closes as soon as the Condair EL hu-
midies.
"Unit on" (Terminal 9 and 10):
This relay closes as soon as the voltage supply
to the Control compartment of the Condair EL is
switched on.
The connecting cable must be led through a cable gland
or grommet into the control compartment.
The maximum contact loading is 250V/8A.
Appropriate suppressor modules are to be used for the
switching of relays and miniature contactors.
65

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Condair RS wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Condair RS

Condair RS Bedienungsanleitung - Englisch - 80 seiten

Condair RS Bedienungsanleitung - Holländisch - 80 seiten

Condair RS Installationsanweisung - Holländisch - 76 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info