652338
64
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
64 Mounting and installation work
Connecting an ohmic humidity controller (passive)
140Ω...10kΩ
A2
CONTROL
V+ IN GND
JP2 (24V)
JP1 (10V)
Control compartment
The signal cable of an ohmic humidity controller
(140Ω...10kΩ) is to be connected according to the wir-
ing diagram to the terminals "V+", "IN" and GND" on
the driver board in the control compartment.
The connecting cable must be led through a cable gland
into the control compartment.
Note: when connecting an ohmic humidity controller
Jumper "JP2" must be removed and Jumper "JP1" must
be connected on the driver board and the control signal
type must be set to 0-10V in the control settings of the
control software.
Connecting a 24V On/Off humidistat
On/Off
A3
CONTROL
V+ IN GND
JP2 (24V)
JP1 (10V)
Control compartment
The signal cable of 24V On/Off humidistat is to be
connected according to the wiring diagram to the ter-
minals "V+" and "IN" on the driver board in the control
compartment.
The connecting cable must be led through a cable gland
into the control compartment.
Note: when connecting a 24V On/Off humidistat Jumper
"JP1" must be removed and Jumper "JP2" connected.
Limiter wiring
Connecting an external limiter controller or a humidity sensor
A4
LIMIT
IN GND
+
Z
Control compartment
The signal cable of an external limiter (P/PI continuous
controller) or of a humidity sensor (if the internal P/PI
limiter controller is used) is to be connected according to
the wiring diagram to the terminals "IN" (+) and "GND"
(–) on the driver board in the control compartment.
The connecting cable must be led through a cable gland
into the control compartment.
Note: the limiter must be activated and congured via
the control software accordingly. The admissible limiter
signal values can be found in the technical data table
in the operation manual.
64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Condair RS wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Condair RS

Condair RS Bedienungsanleitung - Englisch - 80 seiten

Condair RS Bedienungsanleitung - Holländisch - 80 seiten

Condair RS Installationsanweisung - Holländisch - 76 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info