Bedienungsanleitung Constructa CD646850 (Seite 21 von 56) (Deutsch, Englisch, Holländisch, Französisch)

715177

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Saturation display

When the metal grease filters or the activated charcoal filter

become saturated, the relevant indicator flashes after the

appliance is switched off:

■ Metal grease filters: |

■ Activated charcoal filter: {

■ Metal grease filters and activated charcoal filter: | and {

If you have not yet done so, the metal grease filters should now

be cleaned or the activated charcoal filter replaced.

Note. The saturation indicator does not apply for non-renewable

activated charcoal filters that are inserted downstream of the

metal grease filter. These activated charcoal filters must be

replaced twice a year.

The saturation indicators can be reset while they are flashing.

Touch the z symbol to do this.

Switching over the display for air circulation mode

For air recirculation mode, the electronic controller must be

switched over accordingly:

■ The extractor hood must be connected and switched off.

■ Touch and hold the # and @ symbols at the same time until

"2" lights up for air recirculation mode (filters that cannot be

regenerated).

■ Touch and hold the # and @ symbols again at the same time

until "3" lights up for air recirculation mode (filters that can be

regenerated).

■ Touch and hold the # and @ symbols again at the same time

until the electronic controller has switched back to air

extraction mode (indicator 1 ).

Audible signal

Switching on

With the fan switched off, touch and hold the # and ' symbols

at the same time for approximately 3 seconds. A signal will

sound as an acknowledgement.

When the signal tone is activated, ‚ will be lit.

Switching off

With the fan switched off, touch and hold the # and ' symbols

at the same time for approximately 3 seconds. A signal will

sound as an acknowledgement.

When the signal tone is deactivated, ‹ will be lit.

Lighting

The lighting can be switched on and off independently of the

fan.

Touch the N symbol.

Set brightness

Press and hold the N symbol until the required brightness is

reached.

Cleaning and maintenance

Cleaning and mai nt enance

: Risk of burns!

The appliance becomes hot during operation. Allow the

appliance to cool down before cleaning.

: Risk of electric shock!

■ Penetrating moisture may result in an electric shock. Clean

the appliance using a damp cloth only. Before cleaning, pull

out the mains plug or switch off the circuit breaker in the fuse

box.

Risk of electric shock!

■ Do not use any high-pressure cleaners or steam cleaners,

which can result in an electric shock.

: Risk of injury!

Components inside the appliance may have sharp edges. Wear

protective gloves.

Caution!

There is a risk of surface damage if you do not peel off the

protective film.Remove the protective film from all parts of the

appliance before using the appliance for the first time.

Cleaning agents

To ensure that the different surfaces are not damaged by using

the wrong cleaning product, follow the instructions in the table.

Do not use any of the following:

■ Harsh or abrasive cleaning agents, e.g. scouring powder or

liquid scouring cleaner,

■ Cleaning products with a high alcohol content,

■ Hard scouring pads or cleaning sponges,

■ Pressure washers or steam cleaners,

■ Cleaning products that dissolve limescale,

■ Aggressive all-purpose cleaning products,

■ Oven spray.

Note: Wash new sponge cloths thoroughly before use.

Note: Follow all instructions and warnings included with the

cleaning products.

--------

Area Cleaning products

Stainless steel Hot soapy water:

Clean with a dish cloth and then dry with

a soft cloth.

Clean stainless steel surfaces in the

direction of the grain only.

Special stainless steel cleaning prod-

ucts are available from our after-sales

service or from specialist retailers.Apply

a very thin layer of the cleaning product

with a soft cloth.

Painted surfaces Hot soapy water:

Clean using a damp dish cloth and then

dry with a soft cloth.

Do not use stainless steel cleaner.

Aluminium and

plastic

Hot soapy water:

Clean with a soft cloth.

Glass Glass cleaner:

Clean with a soft cloth. Do not use a

glass scraper.

Controls Hot soapy water:

Clean using a damp dish cloth and then

dry with a soft cloth.

Risk of electric shock caused by pene-

trating moisture.

Risk of damage to the electronics

caused by penetrating moisture. Never

clean controls with a wet cloth.

Do not use stainless steel cleaner.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Constructa CD646850 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info