Bedienungsanleitung Dali Fazon Sub 1 (Seite 9 von 26) (Deutsch, Englisch, Dänisch)

745209

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

UK DE DK

being overpowering. Bass must be tight and accurate so that the subwoofer reproduces the exact

amount of bass present in the music/soundtrack; no more no less. When installing the DALI FAZON

SUB 1 in a surround sound system, we recommend selecting a ﬁxed level on the sub and adjusting

the subwoofer output using the surround (pre-) ampliﬁer’s setup function.

If bass levels are set too high, distortion will reduce the quality of your listening experience.

Remember that you can boost the bass level by selecting a physical position close to the wall or

even better – in a corner (see chapter “3.0 Positioning”).

5.3 CROSSOVER FREQUENCY ADJUSTMENT

Once you have set the phase and the volume level, you need to adjust the overlap between the

main speakers and the DALI FAZON SUB 1.

5.3.1 USING LINE INPUT (MODE SELECTOR SET TO NORMAL)

The crossover frequency adjustment on the subwoofer is only possible when using the LINE

INPUT(S) given that the MODE selector is set to NORMAL.

On the rear of the subwoofer, adjust the CROSSOVER button upwards until you can hear the bass is

even with no drop-outs (Frequency range 50-150 Hz). Smaller speakers typically require a higher

crossover point, whereas larger speakers will accept a lower crossover point. When connecting

your DALI FAZON SUB 1 to smaller speakers, e.g. the DALI MOTIF LCR or the DALI FAZON SAT, we

recommend a crossover point of approximately 100 Hz (12 o’clock position).

After having adjusted the crossover frequency you may have to re-adjust the volume to

optimise performance.

5.3.2 USING LFE INPUT (MODE SELECTOR SET TO LFE)

When connecting your DALI FAZON SUB 1 to smaller speakers, e.g. the DALI MOTIF LCR or the

DALI FAZON SAT, we recommend a crossover point of 100 Hz. This must be entered in the menu

system of your (pre-) ampliﬁer. You might need to enter the ‘small’ setting when selecting type of

front speakers in the AV receiver menu.

Connecting larger speakers (typically ﬂoor-standing front speakers) will allow you to choose a

lower crossover point, and to deﬁne your speakers as ‘large’ in the menu system.

If in doubt about the capacity of your speakers, we recommend setting the crossover point quite

high, deﬁning your speakers as small, and ﬁnally reducing the crossover point to the lowest

possible position while maintaining an even bass with no drop-outs.

5.4 POWER

The POWER button is the main ON/OFF switch. We recommend switching OFF the subwoofer

when it is not to be used for extended periods. When the POWER button is set to OFF there

will still be voltage inside the subwoofer. If you completely disconnect the subwoofer from the

mains voltage, please be sure to remove the mains plug from the subwoofer. When changing

connections, always disconnect the mains voltage from the subwoofer. We recommend that you

ALWAYS turn OFF the FAZON SUB on the rear side of the subwoofer BEFORE turning off the mains

switch. Be sure that the correct VOLTAGE is selected before switching the POWER ON.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dali Fazon Sub 1 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dali Fazon Sub 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info