Bedienungsanleitung Datalogic PowerScan PBT7100 (Seite 18 von 24) (Englisch)

535543

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

16 PowerScan PBT7100

Cordless Imaging Reader

• The reader may not be programmed to output your barcode data properly. For example,

you scan “12345” and the host displays “A12345B.” Reprogram the reader with the

proper Data Editing selections. Reference the PRG.

• The reader won’t read your barcode at all.

• Scan the part number barcode on the back of this manual or other known-good barcode

samples. If the reader reads sample barcodes, check that your target barcode is readable.

• Verify that your barcode symbology is enabled. See the PRG.

• If you aren’t sure what programming options have been set in the reader, or if you want the

factory default settings restored, go to the Resetting the Standard Product

Defaults

section of this manual and scan the standard factory default settings barcode.

• The reader sounds other than a standard “Good Read” beep followed by an “Acknowledge

”

beep when reading a barcode (indicating the barcode has been read and properly transmit-

ted).

• Verify the reader is linked to and within range of its Base Station.

Datalogic ADC Limited Factory Warranty

Warranty Coverage

Datalogic ADC (“Datalogic”) hardware products are warranted against defects in

material and workmanship under normal and proper use. The liability of Data-

logic under this warranty is limited to furnishing the labor and parts necessary

to remedy any defect covered by this warranty and restore the product to its

normal operating condition. Repair or replacement of product during the war-

ranty does not extend the original warranty term. Products are sold on the

basis of specifications applicable at the time of manufacture and Datalogic has

no obligation to modify or update products once sold.

If Datalogic determines that a product has defects in material or workmanship,

Datalogic shall, at its sole option repair or replace the product without addi-

tional charge for parts and labor, or credit or refund the defective products duly

returned to Datalogic. To perform repairs, Datalogic may use new or recondi-

tioned parts, components, subassemblies or products that have been tested as

meeting applicable specifications for equivalent new material and products.

Customer will allow Datalogic to scrap all parts removed from the repaired

product. The warranty period shall extend from the date of shipment from Dat-

alogic for the duration published by Datalogic for the product at the time of pur-

chase (Warranty period). Datalogic warrants repaired hardware devices against

defects in workmanship and materials on the repaired assembly for a 90 day

period starting from the date of shipment of the repaired product from Data-

logic or until the expiration of the original warranty period, whichever is longer.

Datalogic does not guarantee, and it is not responsible for, the maintenance of,

damage to, or loss of configurations, data, and applications on the repaired

1. Typically, both of these beep indications are active in the reader. To enable/disable these

indications, reference the PRG.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Datalogic PowerScan PBT7100 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Datalogic PowerScan PBT7100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info