Bedienungsanleitung DeLonghi ECAM45.760 Eletta Cappuccino (Seite 6 von 20) (Englisch)

800465

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

119

6. TURNING THE APPLIANCE ON

Please note!

Before turning the appliance on, make sure the main switch

(A20) is pressed (g. 2).

Each time the appliance is turned on, it performs an automatic

preheat and rinse cycle which cannot be interrupted. The appli-

ance is ready for use only after completion of this cycle.

Danger of burns!

During rinsing, a little hot water comes out of the coee spouts

(A7) and is collected in the drip tray (A12) underneath. Avoid

contact with splashes of water.

• To turn the appliance on, press the button (B1-g.

8). The message “Heating up, Please wait” appears on the

display (B13).

When heating is complete, the message changes to “RINSING”.

As well as heating the boiler, this also heats the internal circuits

by circulating hot water.

The appliance is at temperature when the message indicating

the taste and quantity of coee appears.

7. TURNING THE APPLIANCE OFF

Whenever the coee machine is turned o after being used to

make coee, it performs an automatic rinse cycle.

Danger of burns!

During rinsing, a little hot water ows from the coee spouts

(A7). Avoid contact with splashes of water.

• To turn the appliance o, press the button (B1- g.

8).

• The message “Turning o Please wait” appears on the

display (B13), then, if necessary, the appliance performs a

rinse cycle and goes o (standby).

Please note!

If you will not be using the appliance for some time, unplug

from the mains socket:

• rst turn the appliance o by pressing the button;

• release the main switch (A20) at the back of the appliance

(g. 2).

Important!

Never press the main switch while the appliance is on.

8. MENU SETTINGS

8.1 Rinsing

Use this function to deliver hot water from the coee spout (A7)

and from the hot water/steam spout (C6), if inserted, to clean

and heat the appliance’s internal circuit.

Place a container with a minimum capacity of 100 ml under the

hot water/steam spout (g. 7).

To enable the function, proceed as follows:

1. Press the MENU/ESC button (B14) to enter the menu;

2. Press < (B4) or > (B8) (g. 9) until “Rinsing” appears on

the display (B13);

3. Press the OK button (B12-g. 10): the message “Conrm?”

is displayed;

Danger of burns!

Do not leave the appliance unattended while hot water is being

delivered.

4. Press the OK button. “RINSING Please wait” is displayed;

5. After a few seconds, hot water is delivered rst from the

coee spouts, then from the hot water/steam spout (if in-

serted) to heat the appliance’s internal circuit. “RINSING” is

displayed, together with a progress bar which lls gradual-

ly as preparation proceeds;

6. To stop the process press any button or wait for delivery of

water to stop automatically.

Please note!

• If the appliance is not used for more than 3-4 days, when

switched on again, we strongly recommend performing

2/3 rinses before use;

• After cleaning, it is normal for the grounds container (A10)

to contain water.

8.2 Descaling

For instructions on descaling, see section “13. Descaling”.

8.3 Install lter

For instructions on how to install the lter, see section “15.

Water softener lter”.

8.4 Replacing the water softener lter (if

installed)

For instructions on how to replace the lter, see section “15.2

Replacing the lter”.

8.5 Adjust time

To adjust the time on the display (B13), proceed as follows:

1. Press the MENU/ESC button (B14) to enter the menu;

2. Press < (B4) or > (B8) (g. 9) until “Adjust time” is

displayed;

3. Press the OK button (B12-g. 10): the hours ash on the

display;

4. Press < or > to change the hour;

5. Press the OK button to conrm. The minutes ash;

6. Press < or > to change the minutes;

7. Press the OK button to conrm.

The time is set. Press the MENU/ESC button to exit the menu.

8.6 Auto-start

You can set the auto-start time in order to have the appliance

ready at a certain time (for example in the morning) so you can

make coee immediately.

Please note!

To enable this function, the time must already be set correctly.

To enable auto-start, proceed as follows:

1. Press the MENU/ESC button (B14) to enter the menu;

2. Press < (B4) or > (B8) (g. 9) until “Auto-start” appears on

the display (B13);

3. Press the OK button (B12- g. 10). “Enable?” is displayed;

4. Press the OK button to conrm;

5. Press < or > to choose the hour;

6. Press the OK button to conrm;

7. Press < or > to change the minutes;

8. Press the OK button to conrm;

9. Press the MENU/ESC button to exit the menu.

Once the time has been conrmed, activation of auto-start is

indicated by the symbol displayed alongside the time.

To disable the function:

1. Select auto-start from the menu;

2. Press the OK button. “Disable?” is displayed;

3. Press the OK button to conrm.

The symbol is no longer displayed.

8.7 Auto-o (standby)

Auto-o can be set so that the appliance goes o after 15 or 30

minutes, or 1, 2 or 3 hours.

To programme Auto-o, proceed as follows:

1. Press the MENU/ESC button (B14) to enter the menu;

2. Press < (B4) or > (B8) (g. 9) until “Auto-start” appears on

the display (B13);

3. Press the OK button (B12- g. 10);

4. Press < or > until the required operating time (15 or 30

minutes, or 1, 2 or 3 hours) is displayed;

5. Press the OK button to conrm;

6. Press the MENU/ESC button to exit the menu.

Auto-o is now programmed.

8.8 Cup warmer

This function enables the cup warmer to be enabled or disabled.

Proceed as follows:

1. Press the MENU/ESC button (B14) to enter the menu;

2. Press < (B4) or > (B8) (g. 9) until “Cup warmer” appears

on the display (B13);

3. Press the OK button (B12- g. 10). “Enable?” or “Disable?”

is displayed;

DeLonghi ECAM45.760 Eletta Cappuccino Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeLonghi ECAM45.760 Eletta Cappuccino

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info