Bedienungsanleitung Denon AVR-4308A (Seite 32 von 119) (Englisch)

522887

Zoom out

Zoom in

Vorherige Seite

1/119

Nächste Seite



Getting Started Connections Playback Remote Control Multi-Zone Information Troubleshooting

ENGLISH

Speciﬁcations

Error Messages

If the auto setup procedure could not be completed due to speaker installation, the measuring environment, etc., an error

message is displayed. If this happens, check the relevant items, be sure to take the necessary measures, then perform the

auto setup procedure over again.

Error messages (examples) Cause Measures

No microphone or speaker • Included setup microphone is not connected.

• Not all speakers could be detected.

• Connect the included setup microphone to the SETUP MIC

jack on the main unit.

• Check the speaker connections.

Ambient noise is too high

or Level is too low

• Too much noise in the room for accurate

measurements to be made.

• Speaker or subwoofer sound is too low for

accurate measurements to be made.

• Either turn off any device generating noise or move it

away.

• Try again when the surroundings are quieter.

• Check the speaker installation and the direction in which

the speakers are facing.

• Adjust the subwoofer’s volume.

None • Displayed speaker could not be detected.

· The front L and front R speakers were not

properly detected.

· Only one channel of the surround (A) and

surround (B) speakers was detected.

· Sound was output from the R channel when only

one surround back speaker was connected.

· The surround back or the surround (B) speaker

was detected, but the surround (A) speaker

was not detected.

• Check the connections of the displayed speaker.

Phase • Displayed speaker connected with the polarities

reversed.

• Check the polarities of the displayed speaker.

• For some speakers, this error message may be displayed

even if the speaker is properly connected. If you are sure

that the wiring is correct, select “Skip”.

NOTE

Be sure to turn the power off before checking the speaker connections.

Room EQ

Select room EQ setting method.

Option

Select settings for room EQ, mic, etc.

[Selectable items] All

Assign

Direct Mode

Select room EQ use for DIRECT or PURE DIRECT mode.

[Selectable items]

OFF

Mic Select

Select the microphone type if not using supplied mic.

The microphone connected to V.AUX Lch is used.

[Selectable items] Mic

V.AUX L

Parameter Check

Check auto setup measurement results.

This is displayed after the auto setup procedure

is completed.

Spkr Conﬁg Check

Distance Check

Ch. Level Check

Crossover Check

EQ Check

[Items to be checked]

Select “Retry” to make the measurements again.

The auto setup results can be reset to what was originally calculated

by MultEQ XT when “Restore” is selected.

Only a professionally certiﬁed installer should ever connect a

professionally-calibrated microphone to the V.AUX L input on the front

panel.

Setup

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-4308A Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info