Bedienungsanleitung DeWalt D27107 T 3 (Seite 48 von 172) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546219

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

ENGLISH

• Depress the head to allow the blade to cut through timber and enter

the saw kerf (81).

• After completing the cut, release the switch and wait for the saw blade

to come to a complete stop before returning the head to its upper rest

position.

Vertical mitre cross-cut (ﬁ g. S2)

• Loosen the mitre knob (79) and depress the mitre latch (80). Move the

rotating table left or right to the required angle.

• The mitre latch will automatically locate at 15°, 22.5°, 35.3° and 45°

both left and right. If any intermediate angle is required hold the head

ﬁ rmly and lock by tightening the mitre knob.

• Always ensure that the mitre knob is locked tightly before cutting.

• Proceed as for a vertical straight cross-cut.

WARNING: When mitring the end of a piece of wood with a

small off-cut, position the wood to ensure that the off-cut is to

the side of the blade with the greater angle to the fence:

left mitre, off-cut to the right

right mitre, off-cut to the left.

Bevel cross-cut (ﬁ g. A2, S3)

Bevel angles can be set from 48° left to 2° right and can be cut with the

rotating table set between zero and a maximum of 45° mitre position left

or right.

• Loosen the fence clamping knob (91) and slide the upper part of the

side fence to the left as far as it will go.

• Loosen the bevel clamp knob (17) and set the bevel as desired.

• Tighten the bevel clamp knob ﬁ rmly.

• Proceed as for a vertical straight cross-cut.

Compound mitre (ﬁ g T1 - T4)

A compound mitre is a cut made using a mitre angle (ﬁ g. T1) and a bevel

angle (ﬁ g. T2) at the same time. This is the type of cut used to make

frames or boxes with slanting sides like the one shown in ﬁ g. T3.

WARNING: If the cutting angle varies from cut to cut, check

that the bevel clamp knob and the mitre lock knob are securely

tightened. These knobs must be tightened after making any

changes in bevel or mitre.

• The chart shown below will assist you in selecting the proper bevel

and mitre settings for common compound mitre cuts. To use the chart,

select the desired angle “A” (ﬁ g. T4) of your project and locate that

angle on the appropriate arc in the chart. From that point follow the

chart straight down to ﬁ nd the correct bevel angle and straight across

to ﬁ nd the correct mitre angle.

• Set your saw to the prescribed angles and make a few trial cuts.

• Practice ﬁ tting the cut pieces together.

• Example: To make a 4 sided box with 25° exterior angles (angle “A”)

(ﬁ g. T4), use the upper right arc. Find 25° on the arc scale. Follow the

horizontal intersecting line to either side to get the mitre angle setting

on the saw (23°). Likewise follow the vertical intersecting line to the top

or bottom to get the bevel angle setting on the saw (40°). Always try

cuts on a few scrap pieces of wood to verify the settings on the saw.

SET THIS BEVEL ANGLE ON SAW

SET THIS MITER ANGLE ON SAW

ANGLE OF SIDE OF BOX (ANGLE"A")

SQUARE BOX

6 SIDED BOX

8 SIDED BOX

Cutting base mouldings

The cutting of base moulding is performed at a 45° bevel angle.

• Always make a dry run without power before making any cuts.

• All cuts are made with the back of the moulding laying ﬂ at on the saw.

Inside corner

- Left side

• Position the moulding with top of the moulding against the fence.

• Save the left side of the cut.

- Right side

• Position the moulding with the bottom of the moulding against the

fence.

• Save the left side of the cut.

Outside corner

- Left side

• Position the moulding with the bottom of the moulding against the

fence.

• Save the right side of the cut.

- Right side

• Position the moulding with top of the moulding against the fence.

• Save the right side of the cut.

Cutting crown mouldings

The cutting of crown moulding is performed in a compound mitre. In

order to achieve extreme accuracy, your saw has pre-set angle positions

at 35.3° mitre and 30° bevel. These settings are for standard crown

mouldings with 45° angles at the top and 45° angles at the bottom.

• Make test cuts using scrap material before doing the ﬁ nal cuts.

• All cuts are made in a left bevel and with the back of the moulding

against the base.

Inside corner

- Left side

• Top of the moulding against the fence.

• Mitre right.

• Save the left side of the cut.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D27107 T 3 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info