Bedienungsanleitung DeWalt D27107 T 3 (Seite 49 von 172) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546219

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

ENGLISH

- Right side

• Bottom of the moulding against the fence.

• Mitre left.

• Save the left side of the cut.

Outside corner

- Left side

• Bottom of the moulding against the fence.

• Mitre left.

• Save the right side of the cut.

- Right side

• Top of the moulding against the fence.

• Mitre right.

• Save the right side of the cut.

Sawing in the bench mode

• Always use the riving knife.

• Always ensure that the riving knife and blade guard are correctly

aligned.

• Always ensure that the mitre saw is set and locked in 0° mitre.

WARNING: Do not cut metal in this mode.

Ripping (ﬁ g. U1 & U3)

• Set the bevel angle to 0°.

• Adjust the saw blade height.

• Set the parallel fence to the required distance.

• Hold the workpiece ﬂ at on the table and against the fence. Keep the

workpiece approx. 25 mm away from the saw blade.

• Keep both hands away from the path of the saw blade.

• Switch the machine on and allow the saw blade to reach full speed.

• Slowly feed the workpiece underneath the upper blade guard, keeping

it ﬁ rmly pressed against the fence. Allow the teeth to cut, and do not

force the workpiece through the saw blade. The saw blade speed

should be kept constant.

• Remember to use the push stick (23) when close to the blade.

• After completing the cut, switch the machine off, allow the saw blade

to stop and remove the workpiece.

WARNING: Never push or hold the free or cut-off side of the

workpiece.

WARNING: Always use a push stick when ripping small

workpieces.

Bevel cuts (ﬁ g. U2)

• Set the required bevel angle.

• Proceed as for ripping.

Cross-cutting (ﬁ g. V1)

• Set the bevel angle to 0°.

• Adjust the saw blade height.

• Set the mitre fence to 0°.

• Proceed as for ripping, only use the mitre fence to push the workpiece

through the blade.

Bevel cross-cutting

• Set the required bevel angle.

• Proceed as for cross-cutting.

Mitre cuts (ﬁ g. V2)

• Set the mitre fence to the required angle.

• Proceed as for cross-cutting.

Optional attachments

WARNING: Prior to assembling any accessories always unplug

the machine.

Dust extraction kit (ﬁ g. W1 & W2)

WARNING! This machine is provided with two dust extraction

points for use in each mode.

WARNING! Whenever possible, connect a dust extraction

device designed in accordance with the relevant regulations

regarding dust emission.

WARNING! When sawing wood, connect a dust extraction

device designed in accordance with the relevant regulations

regarding dust emission.

Connect a dust collection device designed in accordance with the relevant

regulations. The air velocity of externally connected systems shall be 20m/s

±2 m/s. Velocity to be measured in the connection tube at the point of

connection, with the tool connected but not running.

Connecting - mitre saw position (ﬁ g. W1)

• Connect the one end of the ﬁ rst hose to the dust extraction adaptor (13).

• Insert the other end of the hose into the middle inlet port of the

manifold (128).

• Connect the one end of the other hose to the under-table guard (63).

• Insert the other end of the hose into the outer inlet port of the manifold.

Connecting - saw bench position (ﬁ g. W2)

• Proceed as for mitre saw position, only connect the hose from the

under-table guard to the saw blade guard (21).

Mitre saw extra support/length stop (ﬁ g. A5)

The extra support and length stop can be mounted on the left-hand side

or on the right-hand side, or with two sets on either side.

• Fit the items 31 - 39 onto the two guide rails (32 & 33).

• Use the inclinable support (34) for cross-cutting 210 mm wide boards

(15 mm thick).

Roller support table (ﬁ g. A6)

The roller support table (40) is used to support long workpieces. In mitre

saw mode, the roller support table can be mounted on the left-hand side

or on the right-hand side, or with two sets on either side. In saw bench

mode, it can also be mounted in front or at the rear of the saw table.

Side extension table (ﬁ g. A8)

The side extension table (42) increases the distance from the rip fence to

the blade to 600 mm or more, depending on the rod length ﬁ tted to the

machine and the clamped position of the table. The side extension table

must be used in conjunction with guide rails (32) (option). The adjustable

table is equipped with an engraved scale along its front edge and

mounted on a sturdy base which clamps to the guide rods.

• Fit the extension table to the right-hand side of the machine for

continuity of the distance scale on both tables.

Sliding table (ﬁ g. A9)

This sliding table (43) allows for board sizes to the left of the blade up to

1200 x 900 mm.

The guide rods are mounted on a sturdy alloy extrusion which is quickly

detachable from the machine and yet fully adjustable is all planes.

The fence incorporates a full length measuring tape for quick positioning

of an adjustable stop and an adjustable support for narrow workpieces.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D27107 T 3 Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info