Bedienungsanleitung DeWalt D27107 T 3 (Seite 50 von 172) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

546219

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

ENGLISH

Transporting (ﬁ g. X)

WARNING: Always transport the machine in saw bench mode

with the upper blade guard fitted.

The castor wheels provide an easier transport of the machine.

• Put the machine on the right base side.

• Fold the rear legs into the base

• Fold the front legs out of the base

• Turn the machine straight up.

• Lift the machine by the front legs up to the wheels are in contact with

the floor.

WARNING: When carrying the machine, always seek

assistance.

MAINTENANCE

Your DEWALT power tool has been designed to operate over a long period

of time with a minimum of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of injury, turn unit off and

disconnect machine from power source before installing

and removing accessories, before adjusting or changing

set-ups or when making repairs. Be sure the trigger switch

is in the OFF position. An accidental start-up can cause injury.

Lubrication

The bearings of the motor are pre-lubricated and watertight.

• Slightly oil the rotating table bearing surface where it slides on the lip of

the ﬁ xed table at regular intervals.

• Periodically lubricate the depth of cut screwthread.

• Clean the parts subject to accumulation of sawdust and chips

periodically with a dry brush.

Cam adjustment (ﬁ g. Y1 - Y3)

To take out the clearance between the two tables, proceed as follows:

• Rotate the machine into saw bench mode.

• Remove the screws (138) and the retainer plate (139).

• Loosen the screw (140) of the adjustment cam (141).

• Rotate the adjustment cam using a pair of needle nose pliers.

• Hold the adjustment cam with the pliers and tighten the screw.

• Replace the retainer plate and tighten the screws.

• Rotate the machine into mitre saw mode. Check the force that is

needed to mitre the saw. Repeat the above steps if the force needed is

too high.

Cleaning

Before use, carefully check the upper blade guard, movable lower blade

guard as well as the dust extraction tube to determine that it will operate

properly. Ensure that chips, dust or workpiece particle cannot lead to

blockage of one of the functions.

In case of workpiece fragments jammed between saw blade and guards

disconnect the machine from the power supply and follow the instructions

given in section Mounting the Saw Blade. Remove the jammed parts and

reassembling the saw blade.

WARNING: Blow dirt and dust out of the main housing with dry

air as often as dirt is seen collecting in and around the air vents.

Wear approved eye protection and approved dust mask when

performing this procedure.

WARNING: Never use solvents or other harsh chemicals for

cleaning the non-metallic parts of the tool. These chemicals

may weaken the materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid

get inside the tool; never immerse any part of the tool into a

liquid.

WARNING: To reduce the risk of injury, regularly clean the

table top.

WARNING: To reduce the risk of injury, regularly clean the

dust collection system.

Optional Accessories

WARNING: Since accessories, other than those offered by

DEWALT, have not been tested with this product, use of such

accessories with this tool could be hazardous. To reduce the

risk of injury, only D

EWALT, recommended accessories should

be used with this product.

Consult your dealer for further information on the appropriate accessories.

Protecting the Environment

Separate collection. This product must not be disposed of with

normal household waste.

Should you ﬁnd one day that your D

EWALT product needs replacement, or

if it is of no further use to you, do not dispose of it with household waste.

Make this product available for separate collection.

Separate collection of used products and packaging allows

materials to be recycled and used again. Re-use of recycled

materials helps prevent environmental pollution and reduces the

demand for raw materials.

Local regulations may provide for separate collection of electrical products

from the household, at municipal waste sites or by the retailer when you

purchase a new product.

EWALT provides a facility for the collection and recycling of DEWALT

products once they have reached the end of their working life. To take

advantage of this service please return your product to any authorised repair

agent who will collect them on our behalf.

You can check the location of your nearest authorised repair agent by

contacting your local D

EWALT office at the address indicated in this manual.

Alternatively, a list of authorised DEWALT repair agents and full details

of our after-sales service and contacts are available on the Internet at:

www.2helpU.com.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D27107 T 3 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info