Bedienungsanleitung DeWalt DCE080GS (Seite 18 von 232) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

790944

Zoom out

Zoom in

Vorherige Seite

1/232

Nächste Seite

GB 11. Calculate the Total Error using the following equation:

Total Error = (AA-A) - (BB-B)

12. If your Total Error measurement is greater than the Allowable

Error for the corresponding Distance Between Walls in the

following table, the laser must be serviced at an authorized

service center.

L (Distance Between Walls) Allowable Error

15m (40′) 1.5mm (3/64”)

20m (50′) 2mm (1/16”)

25m (70′) 2.5mm (3/32”)

30m (100’) 3mm (1/8”)

Plumb Error Check

Perform this check using a wall that is no shorter than the tallest wall

for which this rotary laser will be used (Figure N).

1. Using a standard plumb bob as a reference, mark the top and

bottom of a wall. (Be sure to mark the wall and not the oor or

ceiling).

2. Position the rotary laser securely on the oor approximately 1m

(3”) from the wall.

3. Turn the laser on and point the laser dot at the mark on the

bottom of the wall.

4. Using the or arrow on the Remote Control (Figure B 6 or

7), rotate the dot upwards.

5. If the center of the dot scans over the mark on the top of the

wall, the laser is properly calibrated.

Using the Laser

Using the Laser on a Tripod

1. Position a tripod securely and set it to the desired height. Make

sure that the tripod has a 5/8”-11 threaded screw to ensure

secure mounting of the laser unit.

2. Make sure that the top of the tripod is roughly level.

• The laser will self-level only if the top of the tripod is within ±

5˚ of level.

• If the laser is set up too far out of level, it will beep when it

reaches the limit of its leveling range. No damage will be done

to the laser, but it will not operate in an “out of level” condition.

3. Attach a tripod adapter (Figure G 1) to the bottom of the laser

unit (Figure G 2).

4. Place the laser with the attached adapter on the tripod and

screw the threaded knob on the tripod into the female thread on

the tripod adapter.

5. Turn the laser ON and allow it to self-level in horizontal (level)

mode (Figure H 1).

6. If you want to use the laser in vertical (plumb) mode, follow

these steps while the laser is still ON:

• Carefully remove the laser unit from the tripod.

• Remove the tripod adapter (Figure I 1) from the bottom of

the laser unit (Figure I 2) and attach it to the side (Figure

I 3).

• With the laser in the vertical (plumb) position, attach the laser

unit to the tripod (Figure I 4). The Dot rotates down to 6

o’clock.

• Press to make sure the laser rotates.

7. Adjust the rotation speed and controls, as desired (Figure P).

Using the Laser on a Floor

The laser level can be positioned directly on the floor for leveling and

plumbing applications such as framing walls.

1. Place the laser on a relatively smooth and level surface where it

will not be disturbed or exposed to vibration.

2. Position the laser for a level setting (Figure H 1).

3. Turn the laser ON and allow it to self-level in horizontal (level)

mode (Figure H 1).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCE080GS Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info