Bedienungsanleitung DeWalt DCE080GS (Seite 19 von 232) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

790944

Zoom out

Zoom in

Vorherige Seite

1/232

Nächste Seite

4. If you want to use the laser in plumb (vertical) mode, carefully

turn the laser so the keypad is at the top (Figure H 2). The

Dot rotates down to 6 o’clock. Press to make sure the laser

rotates.

5. Adjust the rotation speed and controls, as desired (Figure P).

NOTE:

The laser will be easier to set up for wall applications if the

rotation speed is set to 0RPMs and the remote control is used

to line up the laser with control marks. The remote allows one

person to set up the laser.

Using the Laser With a Laser Detector

How the Detector works

Some laser kits include a DeWALT Digital Laser Detector. The

DeWALT Digital Laser Detector allows you to locate a laser beam

emitted by a rotary laser in bright light conditions or over long

distances.

• The detector can be used in both indoor and outdoor situations

where it is difficult to see the laser beam.

• The detector is not for use with non-rotating lasers but is

compatible with most rotary red-beam (DCE080RS) and green

beam (DCE080GS) lasers.

• The detector can be set to indicate the location of the beam to

either the nearest 2mm (5/64") or the nearest 1mm (3/64").

• The detector gives both visual signals through the display window

(Figure F 6) and audio signals through the speaker (Figure

F 5) to indicate the location of the laser beam.

Detector’s Indicators

Above

Grade

Slightly

Above

Grade

Slightly

Below

Grade

Below

Grade

Audible

Signal

Fast Beep Fast Beep Steady

Tone

Slow Beep Slow Beep

Display

Icon

• The DEWALT Digital Laser Detector can be used with or without

the detector clamp. When used with the clamp, the detector can be

positioned on a grade rod, leveling pole, stud, or post (Figure G).

To connect the detector to the clamp:

• Push in the clamp latch (Figure G 3).

• Slide the tracks on the clamp (Figure G 4) around the rail on

the back of the detector (Figure F 11 ) until the button (Figure

G 5) on the clamp snaps into the latch hole on the back of

the detector (Figure F 12 ).

• Turn the clamp knob (Figure G 6) counterclockwise to open

the jaws on the clamp.

• Place the clamp on the rod (Figure G 2) so that the detector

is positioned at the height needed to work with the laser.

• Turn the clamp knob (Figure G 6) clockwise to secure the

clamp on the rod.

Using the Detector

1. Set up and position the rotary laser that you will be using

according to the manufacturer’s directions. Turn the laser on and

make sure the laser is rotating and emitting a laser beam.

2. Press the power button once on the detector to turn the detector

on.

3. On the bottom of the display window, notice the speaker icon

(Figure F 10 ).

• To decrease the volume of the audible signal, press the volume

button (Figure F 4); both half circles next to the speaker icon

(Figure F 10 ) will dissappear.

• To turn off the audible signal, press the volume button (Figure

F 4) until the speaker icon dissapears from the display

window.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCE080GS Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info