Bedienungsanleitung DeWalt DCE085R (Seite 9 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

790837

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

• If the laser is tilted greater than 10°, the beams will

continually flash 3 times.

5. If the laser beams ash, the laser is not level (or plumb)

and should NOT BE USED for determining or marking level

or plumb. Try repositioning the laser on a level surface.

6. If ANY of the following statements are TRUE, continue with

the instructions for Checking Laser Accuracy BEFORE

USING THE LASER for a project.

• This is the first time you are using the laser (in case

the laser was exposed to extreme temperatures).

• The laser has not been checked for accuracy

in a while.

• The laser may have been dropped.

Checking Laser Accuracy

The laser tools are sealed and calibrated at the factory.

It is recommended that you perform an accuracy check prior

to using the laser for the rst time (in case the laser was

exposed to extreme temperatures) and then regularly to ensure

the accuracy of your work. When performing any of the

accuracy checks listed in this manual, follow these guidelines:

• Use the largest area/distance possible, closest to the

operating distance. The greater the area/distance, the easier

to measure the accuracy of the laser.

• Place the laser on a smooth, at, stable surface that is level

in both directions.

• Mark the center of the laser beam.

Plumb Dot Accuracy

Checking the plumb calibration of the laser can be most

accurately done when there is a substantial amount of vertical

height available, ideally 25’ (7.5 m), with one person on the oor

positioning the laser and another person near a ceiling to mark

the dot created by the beam on the ceiling.

1. Mark point P1 on the oor (Figure G #1).

2. Turn the laser ON and press once to display dots

above, ahead, and below the laser.

3. Place the laser so that the down dot is centered over point

P1 and mark the center of the up dot on the ceiling as point

P2 (Figure G #1).

4. Turn the laser 180°, making sure that the down dot is still

centered on point P1 on the oor (Figure G #2).

5. Mark the center of the up dot on the ceiling as point P3

(Figure G #2).

6. Measure the distance between points P2 and P3.

7. If your measurement is greater than the Allowable

Distance Between P2 & P3 for the corresponding

Distance Between Ceiling & Floor in the following table,

the laser must be serviced at an authorized service center.

Distance Between

Ceiling & Floor

Allowable Distance

Between P2 & P3

15′ (4.5m) 7/64”(2.6mm)

20′ (6m) 9/64” (3.3mm)

30′ (9m) 7/32” (5.4mm)

40′ (12m) 9/32” (7.2mm)

Level Dot Accuracy - Level

Checking the level calibration of the laser unit requires two

parallel walls at least 20’ (6 m) apart.

1. Turn the laser ON and press twice to display dots

above, ahead, below, and to the right and left of the laser.

2. Place the laser 2”–3” (5–8 cm) from the rst wall. To test

the front laser dot, make sure the front of the laser is facing

the wall (Figure H #1).

3. Mark the laser dot position on the rst wall as point P1

(Figure H #1).

4. Turn the laser 180˚ and mark the laser dot position on the

second wall as point P2 (Figure H #1).

5. Place the laser 2”–3” (5–8 cm) from the second wall. To test

the front laser dot, make sure the front of the laser is facing

the wall (Figure H #2), and adjust the height of the laser

until the laser dot hits point P2.

6. Turn the laser 180˚ and aim the laser dot near point P1 on

the rst wall, and mark point P3 (Figure H #2).

7. Measure the vertical distance between points P1 and P3 on

the rst wall.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCE085R Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info