Bedienungsanleitung DeWalt DCE085R (Seite 10 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

790837

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

GB 8. If your measurement is greater than the Allowable

Distance Between P1 & P3 for the corresponding

Distance Between Walls in the following table, the laser

must be serviced at an authorized service center.

Distance Between

Walls

Allowable Distance

Between P1 & P3

20′ (6.0m) 9/64” (3.6mm)

30′ (9.0m) 7/32” (5.4mm)

50′ (15.0m) 11/32” (9mm)

75′ (23.0m) 9/16” (13.8mm)

9. Repeat steps 2 through 8 to check the accuracy of the right

dot and then the left dot, making sure that the laser dot you

are testing is the laser dot facing each wall.

Level Dot Accuracy - Square

Checking the level calibration of the laser unit requires a room

at least 35’ (10m) long. All marks can be made on the oor

by placing a target in front of the level or square beam and

transferring the location to the oor.

NOTE: To ensure accuracy, the distance (D1) from P1 to P2, P2

to P3, P2 to P4, and P2 to P5 should be equal.

1. Mark point P1 on the oor at one end of the room, as

shown in Figure I #1.

2. Turn the laser ON and press once to display dots

above, ahead, and below the laser.

3. Place the laser so that the down dot is centered over point

P1 and make sure the front dot points toward the far end of

the room (Figure I #1).

4. Using a target to transfer the front level dot location on the

wall to the oor, mark point P2 on the floor and then point

P3 on the floor (Figure I #1).

5. Move the laser to point P2 and align the front level dot to

point P3 again (Figure I #2).

6. Using a target to transfer the front level dot location on the

wall to the oor, mark the location of two square beams as

points P4 and P5 on the oor (Figure I #2).

7. Turn the laser 90° so the front level dot aligns to point P4

(Figure I #3).

8. Mark the location of the rst square beam as point P6 on

the oor as close as possible to point P1 (Figure I #3).

9. Measure the distance between points P1 and P6 (Figure

I #3).

10. If your measurement is greater than the Allowable

Distance Between P1 & P6 for the corresponding

Distance (D1) in the following table, the laser must be

serviced at an authorized service center.

Distance (D1)

Allowable Distance Between

P1 & P6

25’ (7.5m) 3/32” (2.2mm)

30’ (9m) 7/64” (2.7mm)

50’ (15m) 3/16”(4.5mm)

11. Turn the laser 180° so the front level dot aligns to point P5

(Figure I #4).

12. Mark the location of the second square beam as point P7

on the oor as close as possible to point P1 (Figure I #4).

13. Measure the distance between points P1 and P7 (Figure

I #4).

14. If your measurement is greater than the Allowable

Distance Between P1 & P7 for the corresponding

Distance (D1) in the following table, the laser must be

serviced at an authorized service center.

Distance (D1) Allowable Distance Between

P1 & P7

25’ (7.5m) 3/32” (2.2mm)

30’ (9m) 7/64” (2.7mm)

50’ (15m) 3/16”(4.5mm)

Using the Laser

Operating Tips

• Always mark the center of the beam created by the laser.

• Extreme temperature changes may cause movement of

internal parts that can affect accuracy. Check your accuracy

often while working.

• If the laser is ever dropped, check to make sure it is still

calibrated.

• As long as the laser is properly calibrated, the laser is self-

leveling. Each laser is calibrated at the factory to nd level as

long as it is positioned on a at surface within average ± 4°

of level. No manual adjustments are required.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DCE085R Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info