Bedienungsanleitung DeWalt DW711 T 7 (Seite 30 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

545014

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH

• Check for damage to the tool, parts or accessories which may

have occurred during transport.

• Take the time to thoroughly read and understand this manual prior to

operation.

Description (ﬁ g. A1–A5)

WARNING: Never modify the power tool or any part of it.

Damage or personal injury could result.

1 On/off switch

2 Head lock up release lever

3 Additional saw bench table locking knob

4 Moveable lower blade guard

5 Fixed table

6 Blade slot

7 Mitre lever

8 Mitre latch

9 Rotating table/mitre arm

10 Mitre scale

11 Fence

12 Bevel clamp handle

13 Hand indentions

14 Mounting holes

15 Riving knife

16 Upper saw blade guard

17 Rip fence

18 Fixed lower guard (for use in bench saw position)

19 Attachment mounting holes

20 Head lock down screw

21 Saw bench table

OPTIONAL ACCESSORIES

22 Material support plate

23 Material clamp

24 Swivelling stop

25 Adjustable stand 760 mm (max. height)

26 Legstand

27 Table end plate

28 Support guide rails

29 Length stop for short workpieces (to be used with guide rails [28])

26 Legstand

30 Roller table

INTENDED USE

Your DW711 table top mitre saw has been developed for professional

cutting wood, wood products and plastics using a nominal 260 mm carbide

tip blade.

DO NOT use under wet conditions or in presence of flammable liquids or

gases.

These table top mitre saws are professional power tools.

DO NOT let children come into contact with the tool. Supervision is required

when inexperienced operators use this tool.

WARNING: Do not use this machine for purposes other

than described.

• This product is not intended for use by persons (including children)

suffering from diminished physical, sensory or mental abilities; lack of

experience, knowledge or skills unless they are supervised by a person

responsible for their safety. Children should never be left alone with this

product.

Electrical Safety

The electric motor has been designed for one voltage only. Always check

that the power supply corresponds to the voltage on the rating plate.

The machine is of class I construction, therefore earthed (grounded)

connection is required.

In case of cord replacement the tool must only be repaired by an authorized

service agent or by qualified electrician.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in the plug.

• Connect the blue lead to the neutral terminal.

• Connect the yellow/green lead to the earthing terminal.

Follow the fitting instructions supplied with good quality plugs.

Recommended fuse: 13 A.

WARNING! 115V units have to be operated via a fail-safe

transformer with an earth screen between primary and the

secondary winding.

Using an Extension Cable

If an extension cable is required, use an approved extension cable suitable

for the power input of this tool (see technical data). The minimum conductor

size is 1.5 mm

; the maximum length is 30 m.

When using a cable reel, always unwind the cable completely.

Assembly and Adjustment

WARNING: To reduce the risk of injury, turn unit off and

disconnect machine from power source before installing

and removing accessories, before adjusting or changing set-

ups or when making repairs. An accidental start-up can cause

injury.

BENCH MOUNTING (FIG. A1)

• Holes (14) are provided in all four feet to facilitate bench mounting.

Bolts with a diameter of 6 mm and 80 mm in length are suggested.

Always mount your saw firmly to prevent movement. To enhance the

portability, the tool can be mounted to a piece of 19 mm or thicker

plywood which can then be clamped to your work support or moved to

other job sites and re-clamped.

• When mounting your saw to a piece of plywood, make sure that the

mounting screws do not protrude from the bottom of the wood. The

plywood must sit flush on the work support. When clamping the saw

to any work surface, clamp only on the feet where the mounting screw

holes are located. Clamping at any other point will interfere with the

proper operation of the saw.

• To prevent binding and inaccuracy, be sure the mounting surface is not

warped or otherwise uneven. If the saw rocks on the surface, place a

thin piece of material under one saw foot until the saw is firm on the

mounting surface.

MOUNTING THE UPPER GUARD (FIG. B)

1. Fasten the guard (16) to the riving knife (15) with the bolt (32), bushing

and nut.

2. Place the bushing through riving knife and guard. Slide bolt (32) through

bushing and fasten with nut. Tighten securely. Ensure flaps (31) on

guard are positioned as shown.

MOUNTING AND ADJUSTING THE RIP FENCE (FIG. C1–C4)

The rip fence consists of a fixed and a sliding fence.

1. Loosen the fence support locking knob (34) which holds the clamping

plate inposition (fig. C1).

2. Slide the fence onto the front of the table using the U-shaped slot as

the guide (fig. C2, C3).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DW711 T 7 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info